22. Fill in the Blanks on the Charts below: Pertains to Individual Feature Only Individual Feature or Related Features Related Features Type of Tolerance Form Profile Orientation Location Runout Geometric Characteristics STRAIGHTNESS CIRCULARITY PROFILE OF A LINE PERPENDICULARITY ANGULARITY TOTAL RUNOUT Symbol ORCOHE $

Q: A uniformly distributed load of q = 44 kN/m is applied across the entire length of an L supported…

A: The uniformly distributed load .The length of the beam is .The beam is simply supported.For S381*64

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: On the toleranced rectangle below, what is the tolerance within which the to be parallel to the…

A: Parallel symbol describes a parallel orientation of one reference feature to a datum surface or the…

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: e hóldéř óf m öf å d to expose th

A: to obtain a mining lease , the holder of a mining claim must absolutely acquire surface rights .

Q: Calculate the Minimum Y distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 I 6.00 0.008 MABC X…

A: given; net distance(Snet)=6tolerance in first circle(T1)=0.008net tolerance in x from both side…

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: I need answers for problems 10, 11, and 12 pertaining to the print.

A: When any dimension enclosed in a parentheses, it will indicates that the given dimension is a…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: Two L6 x 6 x 1 equal leg angles (see Table A-7) are attached back-to-back to form a T-section, as…

A: The maximum allowable stress is

Q: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is…

A: As per Bartleby guidelines, this is a multipart question and we will answer the first three…

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

A:

Q: I need help answering these 3 parts. 1. The size description of an object on the print can best be…

A: The size description of an object on the print can best be described as dimensioning.The correct…

Q: The is the condition in which a feature of size contains the least amount of material within the…

A: Maximum material condition: The condition of the object in which the object have maximum amount of…

Q: suring plan What is the difference between feature How do you measure cylinders C1 or C2

A: Inteoduction we utilize a direction framework to depict the developments of an estimating machine.…

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: Q3/ Draw the front section of the figure (2)? RIO p10 54 p82 $56 76 RI14 FROM ト!2 CENTRE OF BOSS $12…

A: Solution:   The front section of the figure is shown below:

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: Explain the purpose of the feature control frame below clearly and completely. Datum A is the size…

A: A feature control frame used to describe the conditions and tolerance of a geometric control on a…

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: On attached drawing 11A017 ,What is the length of the dovetail slot?   All abbreviations are…

A: In the given drawing the length of the dovetail slot is in the side view. The dovetail slot is…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact…

A: subject : engineering drawing

Q: Using the diagram, determine the minimum clearance, in inches. DIA A 0.000 0 -0001 6" BASIC…

A:

Q: nce and orientation t

A: It is geometric dimensioning and the tolerancing location control used for engineering drawing…

Q: Which type of feature doesn't belong to orientation tolerances?         Concentricity…

A: using datum plane measure the Angularity , Perpendicularity and  Parallelism

Fire safety

Fire safety is a new domain emerged in the early 90s to enable the design of buildings, structures, and infrastructure against destruction through fire. It also includes the provisions of building codes. This field is mostly associated with the design and efficient planning of a building, to reduce the destruction caused by fire. The branch of engineering that deals with it for the safety of the buildings from destruction of fire, is known as fire safety engineering.