suring plan What is the difference between feature How do you measure cylinders C1 or C2

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: how to measure cylinder taper and out of round

A: Cylinder out of Round is the difference of diameter when measured parallel to the crankshaft and…

Q: Why are three views used to show the object?

A: As we all now everything around us can geometrically be defined in the cartesian coordinate system.

Q: Which component on an outside micrometer greatly reduces measurement time? Anvil Spindle Frame Fast…

A: Micrometer: It is a mechanical instrument which is used to measure the precise linear measurements…

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: Cylinder taper is the difference in a cylinders diameter between the bottom of the cylinder bore and…

A: Yes, the given statement is absolutely correct.

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: I have gone through alll your answers in the first part, and upto my knowledge all your answer seems…

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: What sequence of cylinder actions is indicated by the event diagram below?

A: Given:The event diagramTo determine:Sequence of cylinder actions

Q: It is common practice to assign a larger portion of the location tolerance to the hole.

A: Fill in the blanks.

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: What other engine components may have to be used to be machined if the cylinder heads are machined…

A: When machining the cylinder heads on a V-type engine, several other engine components may also need…

Q: ACTIVITY 10-1 Split Type Dowel

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 3-137 For Problem 3-136 estimate the stresses at the inner and outer surfaces at section B- B,…

A:

Q: A single centerline is drawn in Longitudinal Horizontal Circular All

A: 1) ALL   Centerline indicate a circular feature on a drawing. In 2D, most circular features look…

Q: how to postion this locators and ensure conformance with the Production Part tolerances using the…

A: Given Data:   To Find: How to position the 3 given locators.

Q: Sketch a setup and measurement method that may be used to check the runout tolerance. Also show the…

A: To sketch a setup and measurement method to check runout tolerance. and to show acceptable max…

Q: Question 2 ( When creating a solid model part intricate geometry of your part, s True

A: Solidworks or ansys is a software where simpler and more complex designs can be drawn with each…

Q: Draw a sectional front view, top view and side view for Hexagonal bolt (M d mm *L mm)?

A: Given Hexagonal Bolt To find Sectional front view Sectional top view Sectional side view

Q: GER SCALE 9 v 1.3- A 3"-2 ACME .75 1.5 "5 SECTION A-A Ø3.75- D-50 Top and front views of the…

A: Adjusting screw is a screw with threads from 40 to 100 threads per inch. Typically stainless steel…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.