Answered: For using a 200 mm sine bar to inspect…

For using a 200 mm sine bar to inspect an angle on a part. The angle has a dimension of 49º 20’ and the sine bare rolls have a diameter of 35 mm. What is the height of th

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Related questions

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

Q: 37. Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing.…

A: The tolerance for the offset is

Q: Suppose that the length of the steel bar is measured by a number of different observers and…

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer. The…

Q: 25 divisions with 34 divisi

Q: The figure above shows a section of a vernier protractor. What is the smallest reading (in minutes…

A: i)smallest reading measured that is least count LC=10'5=2'

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: igh precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to…

A: Given:Length of sine bar, L=200 mmangle=49o 20'angle=49+2060=49.33oDiameter of rolls, d=35 mm

Q: Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A 0 000 O 00016 BASIC…

Q: Read the micrometer. 10 5 0. 2 تأسست 3 بليل 4 5 -5 0 -20 The length shown on the micrometer is (Type…

A: Given: To find: Micrometer reading=?

Q: Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a…

A: Given data: The time for car is t=5 min=300 sec The covered distance is s=181 m The diameter of the…

Q: Read the following inch vernier caliper setting 8. 1/128in

A: Solution:

Q: R.70 B 4x 1.40 There are 4 arched edges with radius 0.70 inches There are 4 arched edges with…

Q: I tried the degree both 51 and 50.99 but it is incorrect. Plz help.

Q: CHAPTER 51 • Drum Brakes 781 Practice reading a metric drum micrometer by completing the activity…

A: It is an instrument that is used to measure the linear dimensions of the objects.

Q: Draw the SECTION VIEW for Figure 1 with the scale 1:1 on the new drawing paper using all the method…

Q: Match the following term to the phrase that describes it. I had this question answered but number 3…

A: Tolerance is the amount variation is permitted to vary from the original dimension.

Q: Calculate the Total Reading from the figure given below for Least count 0.02mm Vernier caliper Image…

A: Step 1. 0 point (initial) of lower part Step 2. point of coincidence

Q: 5. Given the following sentence descriptions of the geometric tolerance information, correctly…

A: d. The planer surface must be perpendicular with in five thousandths of an inch tolerance zone…

Question

For using a 200 mm sine bar to inspect an angle on a part. The angle has a dimension of 49º 20’ and the sine bare rolls have a diameter of 35 mm. What is the height of the gauge block stack accurate to four decimals.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

high precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to inspect an angle on a part. The angle has a dimension of 49º 20’ and the sine bare rolls have a diameter of 35 mm. The height of the gauge block stack accurate to four decimals is
Suppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Text
High precision in angular measurements can be made using a sine bar. For using a 300 mm sine bar to inspect an angle on a part. The angle has a dimension of 37 45' and the sine bare rolls have a diameter of 40 mm. Determine: (a) The height of the gauge block stack (value accurate to four decimals). (b) The total number of gauges used including protector slips.
For measuring a wire of thickness 1mm , out of a ruler, vernier calipers and Micrometer which one will be more accurate and which one will be less accurate? If the main scale of vernier calipers has calibrations, 1cm divided in two 20 divisions and the vernier scale has 10 divisions on it, what is its least count? 7. Write the correct reading of the micrometer screw gauge given in the figure. mpie 3" mark below 0 10 zero error = Correct reading = ||
Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height is composed of the following gauge block values, 10, 15, 30, 4.5 and 1.3 mm. the length of the sine bar is 140mm. Support your answer with sketch.
A slip gauge setting height 50.14 mm is observed when a sine bar of the length 147.32 mm is used during the precise angle measurement of a workpiece in a workshop. Find the angle of the workpiece in degrees= (Enter at least 4 digits after decimal points)
16q A slip gauge setting height of 65.215mm is observed and an angle of 480 is found during the precise angle measurement of a workpiece in a workshop. Find the length of the Sine Bar used in mm= (Enter at-least 4 digits after decimal points)
The micrometre is a direct measurement device with a least count of 0.01 mm, that has 20 divisions on the thimble. Select one: True O False
High precision in angularmeasurements can be made usinga sine bar. For using a 200 mm sinebar to inspect an angle on a part. The angle has a dimension of 49 degree 20' and the sine bare rolls have adiameter of 35 mm. Calculate the height ofthe gauge block stack is accurate tofour decimals.
Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ0500 -0.312 Oe.005(M A BC C Pattern-4 holes # 2 1.000 # 3 +) 1.500 +)
Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on geometric construction. Dimension must be included. all dimension in mm
stion 18 If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a vernier caliper with 20 division on the vernier scale. yet rered Find Final reading in mm = ed out of ag question O Tyne here to search