200 mm P 200 mm C B 600 mm. 400 mm

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: 150 B D C St Al 50 30 300 N.m 600 500

A: Applied torque, T=300 N-m Diameter of the aluminum section, dAl=50 mm Diameter of the steel section,…

Q: A bracket is riveted to a columm by 6 rivets of equal size as shown in figure. It carries a load of…

A: given; number of rivet(n)=6load(P)=100KN=100*103Ndistance from column(L)=250mmshear…

Q: Due to the applied loading, the element at point A on the solid shaft in Figure is subjected to the…

A: Given:- σx=-12 ksiσy=0τxy=6 ksiTo find:-Principle stress

Q: 5. The position of the rod DE is controlled by the hydraulic cylinder CF. For example, if the…

A: Given            Load, P = 400 lb Bending stress = 15 ksi      Diameter, d = 1/4 inch = 0.25 inch…

Q: The structure of hook is made such that it is in round shape with diameter d= 20mm as shown in the…

A:

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: The given section is as shown below, Calculate the position of NA, Area of the section…

Q: The figure below are 2 solid cylindrical bars joined together at point B. Find the required minimum…

A:

Q: 0.4 m y 0.2 m 0.3 m 0.6 m 5 m EFG kirişinin enine kesiti В 0.25 m 1200 N Q2) As shown in the figure,…

A: Given: The width of the cross-section, b = 25 mm The height of the cross-section, h = 50 mm The…

Q: P Tav P σαν

A: GivenA=0.024 mθ=40oσav=200kPaP=8.18 kNτav=-168 kPa

Q: Cable DB supports canopy beam OABCas shown in the figure. Find the required cross-sectionalarea of…

A: Draw a diagram for the problem. Here, T is the tension in the cable, θ is the angle made by the…

Q: The 40-mm diameter solid shaft ACBD is supported by two bearings at A and B. Due to the transmission…

A:

Q: In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.2 ksi. Ift =…

A: (a) Draw the free-body diagram of joint A.

Q: 4.00kips Ib 600 ft Problem 3. Pin B acts in double shear and has diameter d=3/4 in. Pins are…

A: Given data: The diameter of the pin, dB=34 in. The failure stress is, τfailure=12000 psi. Draw the…

Q: What the maximum stresses in the stepped shaft composite of two materials steel and Aluminum that…

A: Given Data torque=300 N.m Gs=82 GPa Gal=27 GPa Polar moment of inertia,

Q: The figure below shown that the three bars are supported a rigid beam ACE. ar CD is made of steel…

A: Given data, d= diameter of each bar =10 mm σAl=allowable stress for aluminum=120 MPa σsteel=…

Q: A gondola on a ski lift is supported by twobent arms, as shown in the figure. Each arm is offsetby…

A: given; allowable tensile stress (σ)=100MPashear stress(τ)=50MPaweight(W)=12KN…

Q: a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural…

A:

Q: Problem No. 2. A 150-mm-wide steel bar with a butt-welded joint, as shown. SET LOAD P NORMAL STRESS…

A: Given DataP=205kNσn=80MPaτ=40MPaθ=57{taken} C section taken for computing the minimum thickness

Q: A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is held against…

A: Outside diameter = 50 mm Inside diameter = 40 mm Shear stress = 55 Mpa

Q: For the beam below find the normal stress at sections in point (B) and (C) D B 75 kN 35 kN 45 kN…

A:

Q: y T H A (1) B

A: You asking only Area and Polar moment of inertia so i provide only that,i hope you understand.

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A: Given: To find: Resultant shear force at C in y direction Resultant shear force at C in z…

Q: Two horizontal bars ABC and DEF are rigid and originally horizontal and the links CE and DG are 1/4…

A:

Q: For the timber shape neglect friction and find 1-The dimension (b) if the allowable shear stress is…

A:

Q: (a) the maximum (b) the maximum horizontal shear stress in the shaft. tension bending stress in the…

A: The diameter of the solid shaft d =45 mmThe support loadThe length of the sectionAt point B is…

Q: For the truss shown in Figure The cross sectional area of each member is 1000 mm² Find the stresses…

A:

Q: The shaft AD shown in the figure is made of the same material and is subjected to torsional moments…

A:

Q: A car weighing 130 kN when fully loadedis pulled slowly up a steep inclined track by asteel cable…

A:

Q: F2. A circular shaft fabricated from steel is supported at each end by rigid constraints, as shown…

A: Given data: LA=LB=60 in=5 ftT=900 ft.lbdA=2.5 in=0.208 ftdB=2 in=0.1667 ft Need to determine the…

Q: Q5(): For the truss shown in the Figure, if the diameter of pins at A and F are 2 in. and 1.5 in.,…

A:

Q: Figure. rod 2m. 2m. 60

A:

Q: the cross-stctions e-e and f-f, respectively, when a torque T = 800 Nm is applied at point B. Take…

A:

Q: In the beam loading system given below, A is a simple and C is a sliding support. The outer diameter…

A:

Q: Couple-moment M is applied to the beam, which has a cross-section, as shown in the Figure. if M =…

A: According to the question M=458 N.m β=62° We need to find Stresses at point A ,B and D

Q: Tie rod (1) diameter = 11 mm, and it is supported by double-shear at B and D and single-shear at A.…

A:

Q: roblem 1.3-5. The truss shown carries two forces: a horizontal rightward force of 50 kN and a…

A:

Q: A cantilever beam with a width b =100 mmand depth h = 150 mm has a length L =2 m and issubjected to…

A: Equation of Pure Bending:- σy=MI=ER where     M=Bending Moment                σ=Bending stress at a…

Q: A 38-mm-diameter solid steel shaft supports loads PA = 1230 N and Pc = 2170 N, as shown. Assume LAB…

A: Given data:Find:Determine the magnitude and location

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.