Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=83 GPa for steel 300 mm P B. 600 mm

Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=83 GPa for steel 300 mm P B. 600 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

#1-A rod 15oom Cong Matates in a horizmtal plane about a vertical axis thru its center. At ench end f the rod is fastened a' cord o.800m long Each cord kupports a weight W. Find the Epeed f hotation 'n' to ircline each rpm cord at 32° th the verfical. #2 Given: W= 250 N Regis : aー 6-T L-0-800m C- time for | rev.
2m dz - m. None of them اپن For the robot above, please determine Uo (the potential energy of Link #0) OU 9.8 OU = 5.6 OUo = 4,9 OU=19.6 * d₁, d₂ and ₂ are the joint variables m₂ = m₁ = m₂ = m₂ = 1 kg The moment of inertia of the last link is 3 kg.m². The mass centers are located on the middle point of each link.
NAME Question 1 (6/20) ANSWER ON THE YELLOW PAGES The nose wheel of the landing gear of an aircraft is extended and retracted by applying a torque M to the rod BC by means of an shaft located at point B. The rod AO, on which the landing wheel is also located, has a combined mass of 100 kg which may be simplified to a point force at point G. The masses of the bars CD and BC may be neglected. If the point D is located underneath point B, the rod CD is at an angle of 30° to the vertical y-axis. At this position the landing gear should be kept stationary, dynamic effects may therefore be neglected. All components are made out of stainless steel with max=200 MPa and Imax = 75 MPa. ALO d. 800 mm 400 mm 200 mm B 300 D M 500 mm OC 500 mm A D Questions, also draw all relevant free-body diagrams: a. Calculate the magnitude of the reaction force at point A. b. Calculate the minimum diameter of the pin in point A. The connection in point A is realized as shown on the right figure. Use a safety…
Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C by smooth journal bearings. Determine the components of reaction at the bearings if the rod is subjected to the force F. The bearings ar ein proper alignment and exert only force reactions on the rod. F=815m d=1.00m e=1.90 m f=2.20 m 30° 60° B d f 0.75 m
please define the system and provide the free-body diagram with x-y-axis
E Share O Zoom D Slideshow I Draw 보 Edit O Rotate Aframe of two members (A) and (BD) are connected together at pin B. The other ends are pin-supported at A and at D as shown in the figure below. A horizontal force of 500 N is applied on member (AC) at point C. The vertical component ofreaction at pin D is: 500N
B2
k1 = 80 N/mm, k2 = 100 N/mm, k3 = 160 N/mm, F3 = 200 N, F4 = 100 N find displacement in node 3 and 4. Calculate the reaction forces in node 1 and 2. k₁ 12 F3 k₂ 3 k₂ nim FA 4
The plant in the picture has mass of 29 kg, and is hanging at a distance of 1.4 meters from the wall. The horizontal rod has mass of 6.2 kg. Assume that its weight is evenly distributed, therefore it can be treated as a single force at the center of mass. The rod is 2 meters long, and there is a cable at a 23° angle supporting it at the end. Center of mass of rod from the point = 2/2=1m Using the wall as the axis of rotation, find the magnitude of the downward torque, from both the weight of the rod and the weight of the plant. t=458.64Nm a.The downward torque is balanced by the upward torque from the force of tension. Find the magnitude of the force of tension. T=?N b.F is the contact force between the rod and the wall. Using the other horizontal force in the problem, find the horizontal component of F (the normal force) that must be present for the rod to be at equilibrium. Fx=?N c.There is a vertical force from a component of the tension, but this is not enough to balance the…
pls put solution thank u
Refer to Fig. P6–9. Given that the tension T in cable AC is 900 N, determine exerted on point C. 6-9 AC the components of TAC 3.5 m 2 m B. 2 m 4.5 m FIGURE P6-9
The position of the head and neck and the forces acting on the head are shown in the figure. The center of gravity of the head of mass m=9 kg is located at point C. The joint reaction force of F J = 150 N, which makes an angle of α = 30° with the vertical from the point B, is acting on the skull by the neck extensor muscles. The center of the atlantooccipital joint is located at point B. For this flexion position of the head, the neck muscle force FM, which makes an angle of γ with the horizontal from the point A , is effective . (Take the gravitational acceleration g as 9.81 m/s 2. ) Accordingly; a) Calculate the angle γ of the muscle force F M with the horizontal. b) Calculate the muscle strength F M. (Write your result in N units.)