200µ F Q.28: A complex voltage vr=30+50sin1000t-40sin2000t Volt, is applied across the circuit shown in figure beside. Determine the instantaneous total current 1T 102 250 equation and the total consumed. 3mH İr=6.25sin(1000t+25.8°-5.26sin(2000t- (Ans.: 201Amp &, P.-245 4W

200µ F Q.28: A complex voltage vr=30+50sin1000t-40sin2000t Volt, is applied across the circuit shown in figure beside. Determine the instantaneous total current 1T 102 250 equation and the total consumed. 3mH İr=6.25sin(1000t+25.8°-5.26sin(2000t- (Ans.: 201Amp &, P.-245 4W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave…

Q: (a) Determine the average voltage of Vo. 2. Figure B.2 shows a circuit using two silicon diodes with…

A: In this question, We need to determine the average voltage, peak voltage and output voltage…

Q: Quèstion 6 NPN BJT is considered as two diodes their anodes are connected together. True False

A: In this question let us consider what is a transistor and how it can be realized using a 2 diode…

Q: 8.* A single phase bridge rectifier supplies a 1kW washing machine induction motor drive. The…

A: I have written this solution as handwritten solution. Hope you find the perfect solution.

Q: Plot the relationship between excitation current and short circuit current, and Please explain.

Q: For a single-phase half-wave uncontrolled rectifier with (RL) load, find the mean and rms values of…

A: We need to find out the mean and RMS values of the output voltage and draw the circuit diagram and…

Q: Draw the signal after adding -2.5 DC level with the given signal, sketch the new output signal and…

A: A DC shift to a given signal can be added either using a clamper or using a battery connected in…

Q: Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input…

Q: (a) Differentiate the difference and advantage of the synchronous buck converter with a typical buck…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 1.28 For the following peak or ms values of some important sine waves, calculate the corresponding…

Q: XProblem No.2 (P2). A fixed bias NPN BJT (Beta = 80) circuit is connected to a 12VDC supply. The…

Q: dc power supply

A: DC Power Supply

Q: connect the circuit of single phase half- wave controlled rectifier with Ac supply Vs=220 sinwt,…

A: Given: Vs=220 sinωt f=50Hz R=15 ohm L=20MH β=3.37 α=66.4

Q: |Q. 5 What will be the percentage change in SIL if 30% shunt capacitance compensation is done.

A: Given: 30% shunt capacitance compensation done. So, k=0.3

Q: 3 A peak rectifier (peak follower) Cir cuit is given below. Vs is a GOH3 Sinusuidal Vollage with…

A: Given data, Vp=50 Vf=60 HzR=5 kΩVr=2 V

Q: Design a de power supply that generates an average dc output voltage of 12 V across a resistive load…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should be…

Q: In the circuit shown below. Let Vm=37 V and i,=21 mA and Vpq -0.7 V: ip is C0.8 ko 3 ko Vmcos(wt)V…

Q: Derive the expressions for current-voltage I -V relation, short circuit current ISC, and open…

A: IL =generated photocurrent Here P and N are heavily doped. Due to IL voltage across the load will…

Q: Q4//Does Clamper circult change the peak-to-peak (1.c., rms value)? Justfy

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A battery of em.f 4V and prternal. xesistance 2.n is joined to a desistor of 82 calculate the…

A: Given, A battery of EMF 4 V and internal resistance 2 Ω is joined to a resistor 8 Ω,

Q: What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a…

A: Given circuit-

Q: A 50 Hz sinusoidal AC voltage source of peak value V, = 340 V delivers power to a resistive load of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A. A step down dc chopper is connected to an R = 5 2 and L = 10 mH. The de supply voltage is 100 V.…

A: Given , supply voltage is Vin .Output voltage is Vout

Q: Figure Q6a : Rectifier Circuit

A: Rectifier- The combination of circuit which is used to convert alternating current to direct…

Q: 2. For the half-wave uncontrolled rectifier circuit supplying a series resistive- inductive load…

Q: Q3) A. A step down de chopper is connected to an R=52 and L=10 mH. The de supply voltage is 100 V.…

A: For the given load resistance R value we are getting peak to peak ripple current higher value than…

Q: II. In a 220 Vrms, 60 Hz. Source, determine the following values: a) Trigonometric equation b) V…

Q: Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of…

Q: Ac

Q: nse. Quèstion 8 NPN BJT is considered as two diodes their anodes are connected together. True False

Q: 1- Chopper refers to a converter when the average power flow is from the ac to the dc side. 2-…

A: As per the guidelines given to us, we can only provide the solution to the first three questions in…

Q: INCLUDE ALL THE DECIMALS.

Q: Example 33: A thyristor used in a half wave rectifier used 220V, with firing angle 60°, total…

Q: The source is a sinusoid of 120 Vrms, i.e, Vm= 170V, at frequency of 60 Hz, the load esistor R = 5…

A: The solution is given below.

Q: Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input…

Q: 15) The plot below shows the time dependent voltage trace for an unknown ac- voltage source. Using a…

A: For the given waveform as shown above Peak to peak voltage, peak voltage , RMS voltage , time…

Q: For the circuit shown in the Figure, consider silicon diodes with forward drop voltage of 0.7 V. If…

A: Given : The given transformer is of centre tapped transformer hence we have to take the secondary…

Q: Draw the wave shape of the output voltage (VOUT) of the following circuit. Assume both the Silicon…

A: Zener Diode Voltage Limiter A Zener diode is known as a breakdown diode because it operates in the…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

100%

200μF
Q.28: A complex voltage v=30+50sin1000t-40sin2000t
Volt, is applied across the circuit shown in figure
beside. Determine the instantaneous total current
IT
$100
252
equation and the total consumed.
3mH
(Ans.:
301Amp & P--245 4W
ir=6.25sin(1000t+25.8°5.26sin(2000t-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help me
6. A 3-phase full converter is used for charging a battery with an emf 110V and internal resistance of 0.20 for a constant charging current of 10A. Compute the firing angle delay for AC line voltage of 220V. Ans. [67.85°1
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
Q.35 Ans. In the circuit shown, the input V, is a sinusoidal AC voltage having an RMS value of 230 V ± 20%. The worst-case peak-inverse voltage seen across any diode is V. (Round off to 2 decimal places.) > KH A A 390.32 (385.00 to 395.00) KH A KH C= R ww
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
4. By using the OCC describe the relationship between the excitation current and the generated voltage.
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
plzz solve subject:renewable energy systems
The sinusoidal waveform displayed by the CRO is shown in Figure below. The 'time/cm' switch is on 50 ms/cm and the 'volts/cm' switch is on 1 V/cm. Calculate (a) the frequency, (b) the peak to peak voltage (c) the average voltage (d) the r.m.s voltage.
Refer to the circuit. Consider ideal model (V_D=0) of diode circuits. Given V_i =100 Volts peak-to-peak sinusoidal input (+50, -50 Voltage peaks). Determine the peak output voltage during the diode non-conduction cycle.
3C) Calculate the values of the second harmonic (HD2) and third (HD3) as well as AUpzfor each of the circuits in the figure below. 3 Nout Nin 3
A crystalline silicon photovoltaic cell has an open circuit voltage of 0.5V and a short circuit current of 1.8 A at Standard Test Conditions. What is the maximum output power at Standard Test Conditions and at a cell temperature of 50oC? What is the percentage decrease in power per oC? Assume a Fill Factor of 0.70 at 25oC. (As a rule of thumb for crystalline silicon solar cells, the increase in short circuit current is about 0.058% per oC while the decrease on open circuit voltage is 0.30% per oC and decrease in the fill factor is by 0.15% per oC).