(c)A 50 Hz sinusoidal AC voltage source of peak value V, = 340 V deliverspower to a resistive load of 50 n.(1) Calculate the average power delivered.(i) The AC source is now connected to the load via a full wave diodebridge. The turn-on voltage of the diodes is 0.3 V. Calculate the peakvoltage across the load and the average voltage across the load.(ii) Explain how a smoothing capacitor can be used to hold up the voltageacross the load. Compare the efficiency of the rectifier with and withoutthe smoothing capacitor.(iv) Define "regulation" as applied to the output voltage of a rectifier andexplain why an LR filtered rectifier bridge provides better regulation ofthe load voltage than an RC filtered rectifier bridge.

“Since you have asked multiple question, we will solve the first question for you. If you want any…

Answered: A 50 Hz sinusoidal AC voltage source of…

A 50 Hz sinusoidal AC voltage source of peak value V, = 340 V delivers power to a resistive load of 50 n. (c) (i) Calculate the average power delivered.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn?
A 100.0 Hz sinusoidal alternating current of peak value 0.25 A is passed through a 40.0 Ω resistor. Calculate: the time period of the alternating current, the peak & r.m.s. voltages across the resistor, and the mean power supplied to the resistor.
Q1: For the waveform of Figure below, Determine: 4v (mV) i) The peak value is mV 8 ii) The peak-to-peak value is mV iii) The period of the waveform, us 3. 4 7 10 t (us) iv) How many cycles are shown, ? v) The instantaneous value of voltage at 9 us is
Please draw the voltage and current curves versus ωt for capacitor with sinusoidal AC power supply. Explain the phase shifting of capacitor.
Answer item 1 only!
the two alternating e.m.f.s would reach their maximum and zero values at the same time such alternating voltages or (currents ) said to be: Phase with each other In phase with each other
3.The voltage generated across one inductor of an alternator is 8.11V. There are 120 slots and 4 turns in every coil. The conductors are all in series and connected in double layer lap windings distributed sinusoidally in several slots. The coil pitch is 10 slots, frequency is 60 Hz and synchronous speed is 720 rpm. Calculate the line-to-line generated voltage if the alternator windings are connected wye. a. 2400Vb. 4160Vc. 4800Vd. 856V
An AC voltage an RMS value and average value of 200 Volts and 150 Volts respectively. What is the form factor of AC Voltage? 1. 1.11 2. 0.75 3. 1.33 4. 1.414
5.) Calculate the inductance or capacitance in series for the impedance 502-60° ohms. Assume the frequency to be 50 Hz. Express in four decimal places.
A single phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?
8. Determine the rms current I as shown in figure 3. Source voltage is already in RMS value (Answer must be in polar form and should be in 4 decimal places). -is A -18 0 ) 220/- 30° V Figure 3. 9. Referring to figure 3, determine the rms current at j50 reactance (inductor) using KCL (Answer must be in polar form and should be in 4 decimal places). (1 10. Referring to figure 3, determine the rms voltage at j50 reactance (inductor) using KVL (Answer must be in polar form and should be in 4 decimal places).
A three – phase 11 kV wye connected synchronous alternator has a synchronous reactance of 8 ohms per phase but negligible resistance. If the excitation is such that the open circuit voltage is 14kV, determine the power factor at the maximum output. a. 0.786 b. 0.772 c. 0.793 d. 0.708