What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph. ZenerDiode Vout V1 R1 ´1k 21ms 7 Draft11 Cursor 1 Vivout) Horz: 21.00271ms Vert: 7.7706735V Cursor 2 Horz - N/A- Vert -N/A-- Dif (Cursor2 - Cursor1) Horz: -- N/A- Vert N/A-- Freg - N/A- Slope N/A--

What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph. ZenerDiode Vout V1 R1 ´1k 21ms 7 Draft11 Cursor 1 Vivout) Horz: 21.00271ms Vert: 7.7706735V Cursor 2 Horz - N/A- Vert -N/A-- Dif (Cursor2 - Cursor1) Horz: -- N/A- Vert N/A-- Freg - N/A- Slope N/A--

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
Determine the maximum value of Vi that will maintain the Zener diode in the on' state given Vz=13V, Izw=63MA, R=3150, RL=1.2ka. Vz Lütfen birini seçin: a.21.9V b.94.2V c.36.3V d.56.1V e.86.4V
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
Please find the correct answer by solving the problem
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph .
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9