20 MPa 60 MPa

Q: The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is…

A: The above-mentioned question from Solid Mechanics require a Mohr’s Circle to solve for ease of…

Q: Two 1.2-kip forces are applied to an L-shaped machine element AB as shown. Determine the normal and…

A:

Q: The control arm is subjected to the loading shown. Determine to the nearest the ¼-in. required…

A: The diameter at pin C to nearest the 1/4-in is dc = 3/4-in.

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the internal…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: e of stress

A:

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: Several forces are applied to the pipe assembly shown. Knowing that Q= 250 Ib and that the pipe has…

A:

Q: 3. Determine the largest shear force V that the member can sustain if the allowable shear stress is…

A:

Q: 5. The steel tube has an elliptical cross section of mean dimensions shown and a constant thickness…

A:

Q: If the applied shear force V = 18 kip, determine the maximum shear stress in the member.

A: Given Data: V=18 kip   To Find: The maximum shear stress in the member.

Q: For the given state of stress, determine the normal and shearing stresses after the element shown…

A: Given, σx = 8 ksi σy = -12 ksi τxy = -6 ksi σx+σy2=8+(-12)2 =-2 ksi σx-σy2=8-(-12)2 =10 ksi…

Q: The motor delivers 50 hp while turning at a constant rate of 1350 rpm at A. Using the belt and…

A: Draw the schematic diagram for the above problem.

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: A 6-kip force is applied to the machine element AB as shown. Knowing that the uniform thickness of…

A:

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx =-8 ksi σy =12 ksi τxv=-6 ksi To draw:- Mohrs circle

Q: Determine the largest allowable diameter of a 10-ft-long steel rod (G= 11.2 × 106 psi) if the rod is…

A: Given: The length of the steel rod is L=10 ft. The shearing stress in the steel rod is τ=12 ksi. The…

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: The propeller shaft of the tugboat is subjected to the compressive force and torque shown. If the…

A: Given Data: The inner diameter of the shaft is d = 100 mm. The outer diameter of the shaft is D =…

Q: Consider the loading shown. The allowable normal stress for the steel used is 172 MPa. For the…

A:

Q: A 240-kip load P is applied to the granite block shown. Determine the resulting maximum value of (a)…

A: a) Maximum normal stress can be determined as

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx=-12 ksi σy=0 ksi τxy=-6 ksi To draw:- Mohrs circle

Q: For the state of stress shown, determine the maximum shearing stress when (a) ơ, = 0, (b) ơz = 60…

A: σavg=1230+100 =6512σx-σy=1230-100=-35

Q: Problem #2: The solid shaft has a diameter of 40 mm. determine the absolute shear stress in the…

A: Given:- d=40 mm To find:- Absolute maximum shear stress Shear stress distribution diagram

Q: Problem 2. The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.