20 kip B 1'ft 1.5 ft 2'ft -1.5 ft- H 1'ft

Q: Determine the diameter of rivet for the eccentrically loaded riveted joint if the permissible shear…

A:

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

A:

Q: Problem 6. The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits…

A: Given: The outer radius of pipe ro=20 mm=0.02 m The inner radius of pipe ri=15 mm=0.015 m Distance…

Q: The pole BC is supported by a pin C and by the steel wire AB. A horizontal force of 30 kN is acted…

A: Given data, Horizontal force at E, FE = 30 KN Ultimate shear stress of the pin, 𝞽ut = 100 MPa…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: B Given: The rigid bar is pinned at A and supported by two aluminum rods, each having a Diameter =…

A: GIven data: The magnitude of the force P acting at the end B of the rigid bar AB is P = 50 kip. The…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 14 kN applied at A. Assume a…

A: Given data: F1=14 kNa=290 mmb=110 mmc=70 mmθ=40°dp=25 mmt=25 mm Need to determine the shear stress…

Q: If the allowable bearing stress for the material under the supports at A and B is o, = 770 psi,…

A:

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C ea have…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 600 psi,…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is o₂ = 810 psi,…

A: FBD

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 16 mm. Assume…

A:

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A:

Q: Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free…

A:

Q: Provide final answer and equations used.

A:

Q: If the allowable bearing stress for the material under the supports at A and B is b = 800 psi,…

A: Given that: Cross sectional area of the beam  = 5*5 in2 Maximum stress = 800 psi Under the given…

Q: allowable bearing stress for the material under the supports at A and B is σ₂ = 780 psi, determine…

A:

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: To find:  The maximum value of Pmax supported by structure. Given:  The diameter of rod is d=13 mm1…

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: For the connection shown, the average shear stress in the 11-mm-diameter bolts must be limited to…

A:

Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…

A:

Q: A column of intermediate length buckles when the compressive stress is 40 ksi. If the slenderness…

A: Given data: The compressive strength of the column, σcr = 40 ksi. The slenderness ratio of the…

Q: B D The rods AB and CD are assumed to be pin connected at A and C. If the cable BD and CD are made…

A: Draw the free body diagram as follows.

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A:

Q: The horizontal bar shown is pinned at O and is supported with a helical spring at L1 from O. L1=2m,…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: 1- For the tapered bar shown with cross sectional areas A-0.02 m² and A 0.01 m² at each end. The bar…

A: In the question load is 4500N but in the diagram given load is 4000N , So I am solving with 4000…

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: A column is clam- ped at the bottom and is carrying a vertical load F, at the center of F. F the top…

A:

Q: The five-bolt connection must support an applied load of P = 4300 lb. If the average shear stress in…

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 10 mm. Assume…

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 12 mm. Assume…

A:

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Given:The diameter of solid rod, d = 13 mmThe diameter of hole, D = 18 mmThe thickness of support…

Q: Tube with 100 mm long and 20 mm diameter. If the axial load is 300ON is applied to it. Determine the…

A:

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 720 psi,…

A: FBD

Q: If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can…

A:

Q: The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When…

A:

Q: Let's consider an axially loaded member having solid circular cross-section and subjected to th…

A: The details provided in the questionThe diameter and the length of the AB section is 30mm and 1 m…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 12 kN applied at A. Assume a…

A:

Q: EVENTS CEV Opsi, determine the maximum load Pmax that TL

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.