20 in. For the beam shown, calculate M, and confirm that the area of tension steel exceeds the required minimum area steel. Ignore compression reinforcement. f'c = 4000psi and f, = 60ksi 4 No. 9 bars 12 in. d = 17.5 in.

20 in. For the beam shown, calculate M, and confirm that the area of tension steel exceeds the required minimum area steel. Ignore compression reinforcement. f'c = 4000psi and f, = 60ksi 4 No. 9 bars 12 in. d = 17.5 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forçes P, = 12 kN, P2-8 kN. and P3 = 6, kN. The lengths of the segments of the bar are a = 1:5 m, b = 0.6 m, ạnd c = 0.9 m. (a) Assuming that the modulus of elasticity E = 210 GPa, calcuļate the change in length & of the bar. Does the bar elongate or shorten? (b) By what amount P should the load P, be increased so that end D of the bar does not move when the loads are applied? %3D P1 P2 P3 A в a b
2/3 700 mm 1) A typical cross-section of a properly reinforced con-crete beam is shown in the figure below. The material properties are summarized below. Use an effective depth of 600 mm. 500 mm Given: fy = 400 MPa = 0.65 75% = 0.85 E = 200 000 MPa Y See the Table 1 f' 48MPa - Bar : 3-30M a) Is the beam properly reinforced/over-reinforced/ balanced Determine the factored moment resistance? b) Consider the beam section "a) "above. However, due to embedded items, the reinforcing is raised by 65 mm, such that the effective depth is reduced to 585 mm (Draw the new cross-section view). Find the factored moment resistance considering the new reinforcement layout. c) Comment on the effect of the change in reinforcement location on the moment resistance d) Refer to the beam section from Part "b" above. The same contractor reported that, due to some problems related to batching, the actual 28-day concrete strength is reduced by 10%. What is the new F'c? Find the factored moment resistance for…
Determine the flexural capacity of the given section of beam below. b=300 d=400 d'=70 fc'=20.7 fy=415 As=4-28mm As'=2-28mm A.USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu kN-m
H= 3 R= 1 Inputs: • Center of Circle is the SAME as the Rectangle. • H= Height in cm (From Table) ● R = Radius of Circle in cm (From Table) Required: For the composite area: 1. Locate the centroid in x and y. 2. Draw the Centroidal Axis. 3. Find the Moment of Inertia around centroidal x axis only. ↑A А D 8 cm R 16 cm 3 cm B C E H cm F X
Do not round off in between solutions and box your final answer. Correct answer should be 970.583, , 890.559, 890.560
Do not round off in between solutions and box your final answer. Correct answer should be 451.041, 446.285
Topic: Quantity surveying 2.) The geometric method breaks the excavation into geometric shapes and calculates the volume for each of the shapes. true or false 3.) The data needed in estimating the roofing material are their effective widths and length in which they are available in the market. true or false 4. Because most equipment is not used on a project for an entire year, the costs must be converted to an hourly, weekly, or monthly cost. true or false
anwser part 4
Given the truss and loading shown below, determine the stress at member DF if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8 @ 10' = 80' Pu B Pu CF Pu et LK J I H G F 8@10' 80' RE
Assume that the truss is simply supported at joints M and E. Determine the stress at member DE if Pu = 18.375 Kips, the area is 23 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a: 10' - J I H G K F * (a ' - RI Rv 8@10'=80
d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
For the cross-section shown below, determine the maximum amount of tension reinforcement (A.) so that the beam cross-section is tension-controlled. [hint: use the strain diagram shown below]. Use fy = 60 ksi and fe=4 ksi. b=12 in. E, = 0.003 †d'= 2.5 in A' =2#9 n.a. d=17.5 in A = ? E, = 0.005