Problem 1 b = 14 in %3D Determine the nominal flexural strength, Mn, of the rectangular section shown in the figure, given f = 3,000 psi, fy = 40 ksi, b = 14 in, d = 21.5 in, and A, = 4 x #10 bars. %3D %3D d = 21.5 in %3D %3D %3D A, = 5.08

Problem 1 b = 14 in %3D Determine the nominal flexural strength, Mn, of the rectangular section shown in the figure, given f = 3,000 psi, fy = 40 ksi, b = 14 in, d = 21.5 in, and A, = 4 x #10 bars. %3D %3D d = 21.5 in %3D %3D %3D A, = 5.08

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the column section below. It has eight #9 bars. The material properties are as follows: fr =4,000 psi, f, = 60 ksi, and E. = 29,000 ksi . The cross-sectional area of a #9 bar is 1.0 in.2². 8- #9 0000 2.5" 44 Axis of bending 20" 15" 2.5" 20" P M If the tensile strain in the reinforcing bars cannot be lower than 0.007 when its nominal moment capacity is reached, using the principles of mechanics to determine the maximum axial load n P, that can be carried by the column. Determine the corresponding nominal moment capacity Mn. (you cannot use any design aid) (Ans: Pn = 246 kips, Mn = 460 kip-ft)
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
Quiz1
Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The cross-sectional areas are Asteel = 80 x 10-³ m² and ABrass = 50 x 10-³ m², and Young's modulus - of steel and brass are 200 MPa and 120 MPa. 100 kN (a) 3.13 mm (b) 7.25 mm (c) 7.5 mm (d) 3.5 mm Steel 50 kN 0.5 m B Brass 0.3 m C Figure 8. A shaft of different diameters Steel 0.5 m Ꭰ 150 kN
Q4: The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8 kip. If the 1.5-in. side changed its length to 1.500132 in., determine the Poisson's ratio. Assume modulus of elasticity (E) = 10 x 10^3 ksi 1.5 in.j 2 in. 8 kip- 8 kip 3 in.-
3. The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18M block is attached. Each steel bar has an area of 566 mm^2 and E=200GPa. For the bronze bar, the area is 866 mm^2 and E=83GPA. Find the stresses developed in each bar. Steel L=Im Bronze L=1.6 m Steel L=Im 18 Mg
h P a C +. P
Someone can help me with this please
5
Learning Goal: The member shown is subjected to a compressive stress in the x direction of o₂ = 400 ksi and a compressive stress in the y direction of oy = 700 ksi The dimensions of the member are a = 3.75 in, b = 1.50 in, and t = 0.75 in. Assume that E - 29000 ksi and that Poisson's ratio is v= 0.29.(Figure 1) Figure V o 9 1 of 1 ▼ Part D - Change in dimension of the member The applied stresses cause the member to experience a change in all of its dimensions. What are the new dimensions, d', b', and t', of the member due to the applied stresses? Express your answers in inches to three significant figures separated by commas. ► View Available Hint(s) d', b',t' = Submit == Provide Feedback 175) ΑΣΦ ΠΨΓ 41 vec → 0 in, in, in Next > 10:55 PM
2/3 700 mm 1) A typical cross-section of a properly reinforced con-crete beam is shown in the figure below. The material properties are summarized below. Use an effective depth of 600 mm. 500 mm Given: fy = 400 MPa = 0.65 75% = 0.85 E = 200 000 MPa Y See the Table 1 f' 48MPa - Bar : 3-30M a) Is the beam properly reinforced/over-reinforced/ balanced Determine the factored moment resistance? b) Consider the beam section "a) "above. However, due to embedded items, the reinforcing is raised by 65 mm, such that the effective depth is reduced to 585 mm (Draw the new cross-section view). Find the factored moment resistance considering the new reinforcement layout. c) Comment on the effect of the change in reinforcement location on the moment resistance d) Refer to the beam section from Part "b" above. The same contractor reported that, due to some problems related to batching, the actual 28-day concrete strength is reduced by 10%. What is the new F'c? Find the factored moment resistance for…
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar