1.40 A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions b and t so that the joint is as strong as the boards. 12 kN P 1.75 in. b|| b +100 mm P 5.75 in. 12 kN FIG. P1.40 FIG. P1.41 +120 mm-

1.40 A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions b and t so that the joint is as strong as the boards. 12 kN P 1.75 in. b|| b +100 mm P 5.75 in. 12 kN FIG. P1.40 FIG. P1.41 +120 mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Please make work and answers legible and easy to find. Thank you!
There is a system located in three-dimensional space like the one shown in the figure, it determines: a) the unit vector of the tensor D, b) the force exerted by the tensor D and c) the tension forces at points B, C D 5m 2m 3 m 250kgf
Do this handwritten I have attached the final answer too
Suppose we have a uniform beam that is 3.40metres long has a flexural rigidity of 31915N Find the deflection of the beam in millimetres if the beam is under a uniform load of 24Nmand is supported with simple supports at both ends. Fill out the table below with your answers. x�-coordinate Deflection (mm��) x=0.14 y(x)�(�) = x=1.12 y(x)�(�) = x=1.80 y(x)�(�) = x=2.65 y(x)�(�) = x=3.06 y(x)�(�) = Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within ±0.0005±0.0005 of the correct answer to be considered correct.
a h a The profile above depicts two joined profiles, each of width h. Find the centroid, X.of the total profile given that a = 145 [mm) h = 10 (mm) 1. 1. What is X? (The gi component of the centroid, in mm) 2. 2. What is X? (The g component of the centroid, in mm)
a) Find the deformation volume of the unit cube b) Find the deformation of area of OABC X3,x3 X1,x1 Function of motion: In[1]= x1 = (1+t) * X1 x2 = -X3 x3 = X2 B A X2,x2
Identify the Degree of Hyperestaticity and define the Main System, indicating the State of Displacement and the State of Virtual Load.
Determine the shape factor of the cross section.
For the 2d coordinate system below, complete the following: a) Break up the force vector into Fx and Fy components; show these components on the figure. Add a superscript to each component to indicate whether they are acting in the positive (+) or negative (-) direction b) Draw a position vector from the origin (0) to the tail (point a) of the force vector c) Break up the position vector into rx and ry components; show these components on the figure Add a superscript to each component to indicate whether they are acting in the positive (+) or negative (-) direction d) Calculate the "moment" of force F about the origin by multiplying F times its perpendicular distance from the origin (ry), and add the product of Fy times its perpendicular distance from the origin (rx). Assume that a counterclockwise rotation about the origin is a "positive" moment. Think of rx as a string connected to the origin. If you pull the string in the direction of d, will that cause a clockwise (-) or…
I need hand written solution only.
Write two other names given to flexibility method and justify these names. b) Prof that f= 1/s. c) What is conjugate beam and list the properties of conjugate beam.
Please answer it clearly with FBD, I will vote it up for your effort thank you.