Concretes have several properties. Which one of the following statements is incorrect? a. Concretes have good tensile strength b. Concretes have good shear strength c. Concretes have good compressive strength d. Concretes have good wear resistance

Concretes have several properties. Which one of the following statements is incorrect? a. Concretes have good tensile strength b. Concretes have good shear strength c. Concretes have good compressive strength d. Concretes have good wear resistance

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.6P

See similar textbooks

Related questions

Q: Concrete is required for a column that will be moderately exposed to freezing and thawing. The cross…

A: Target mean strength: It is the design strength determine for the manufacture of reinforced…

Q: 1.41 Estimate the tensile strength required to prevent cracking in a concrete-like material that is…

A: Given Length L = 50 in initial temperature =100oF Final temperature = 0oF α=5×10-6/FoE=5×106psi To…

Q: (a) One of the advantages of concrete is its high strength to weight ratio compared to other…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: A. What are the primary and secondary parameters upon which durability of concrete depends on?…

A: Durability of concrete: It is defined as the ability of concrete to resist the actions of external…

Q: T 1. The "slump" test is used to determine the compressive strength of a concrete. F (F 2. For room…

A: Note:- I'm explaining the top three parts here. For all other parts kindly resubmit the question. 1.…

Q: Concrete is strongest when subjected to: OA Tension O B) Bending O9 Torsion

A: 1. The concrete is strongest when subjected to:

Q: For concrete production, we mix 625 kg of fine aggregate and 830 kg of coarse aggregate. The fine…

A: The moisture content is also known as water content- It is defined as the ratio of the weight of…

Q: An elastoplastic material with strain hardening has the stress-strain relation shown below. The…

A: As per the given data first we have to draw the stress and stress curve to understand the curve and…

Q: The biggest economic advantage of CMU over concrete is: it is less labor intensive it can be…

A: CMU STANDS FOR CONCRETE MASONRY UNIT.

Q: What is the weakest property of concrete? The compressive strength of the coarse aggregate The…

A: What is the weakest property of concrete?The compressive strength of the coarse aggregateThe…

Q: what are the different types of resin cements in dentistry and their indications

A: Determine:

Q: Two composite bars have the following composition. At an initial temperature of 5 degree C. there is…

Concept explainers

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.

Question

Concretes have several properties. Which one of the following statements is
incorrect?
a. Concretes have good tensile strength
b. Concretes have good shear strength
c. Concretes have good compressive strength
d. Concretes have good wear resistance

Expert Solution

Step 1: given statement

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Estimate the transverse tensile strength of the concrete in Problem 12.6.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
In Example Problem 12.1, a uniaxial composite material is made into a circular rod Vbith a 1.27-cm diameter from 70 volume percent continuous carbon fibers and 30 volume percent epoxy. The rod is subject to an axial force of 100,000 N. The composite matcrial in Example Problem 12.1 is to be replaced with a less expensive composite made of 70 volume percent continuous E-glass fibers and 30 volume percent epoxy. The elastic moduli are 5 GPa for the epoxy resin and 72.4 GPa fos the E-glass. (a) Compare the elastic modulus, composite strain, fiber and matrix stresses, and density of this composite with the carbon epoxy composite in Example Problem 12.1. Usc the density of UHM carbon, and assume the density of the epoxy is 1.2g/cm3 . (b) Can both the E-glass fiber and matrix withstand the applied force?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.