Concrete is required for a column that will be moderately exposed to freezing and thawing. The cross section of the column is 300 × 300 mm. The smallest spacing between reinforcing steel is 30 mm. The specified compressive strength of concrete at 28 days is 40 MPa with a slump of 80 to 100 mm. The properties of materials are as follows: Cement used is type I Portland cement with a specific gravity of 3.15. The available coarse aggregate has a maximum size of 23 mm, a dry-rodded unit weight of 1800 kg/m3, a bulk specific gravity (SSD) of 2.7, absorption capacity of 0.55%, and moisture content (SSD) of 0.25%. The fine aggregate has a bulk specific gravity (SSD) of 2.75, absorption capacity of 1.4%, a moisture content (SSD) of 2.5%, and a fineness modulus of 2.70. The aggregates conform to the ASTM C33-84 requirements for grading.

Concrete is required for a column that will be moderately exposed to freezing and thawing. The cross section of the column is 300 × 300 mm. The smallest spacing between reinforcing steel is 30 mm. The specified compressive strength of concrete at 28 days is 40 MPa with a slump of 80 to 100 mm. The properties of materials are as follows: Cement used is type I Portland cement with a specific gravity of 3.15. The available coarse aggregate has a maximum size of 23 mm, a dry-rodded unit weight of 1800 kg/m3, a bulk specific gravity (SSD) of 2.7, absorption capacity of 0.55%, and moisture content (SSD) of 0.25%. The fine aggregate has a bulk specific gravity (SSD) of 2.75, absorption capacity of 1.4%, a moisture content (SSD) of 2.5%, and a fineness modulus of 2.70. The aggregates conform to the ASTM C33-84 requirements for grading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5 - Why dolomitic aggregate is not preferred in concrete.A) Increases the vacancy rate.B) It creates expansion.C) AllD) Because it is inertE) Increases permeability.
What is maximum capacity of measure should be used in determining the density of the concrete if the nominal maximum aggregate size of coarse aggregate is 25.0 mm?
Use ACI method .
Cracking Analysis of Reinforced Concrete ANSWER A. TO G. COMPLETE SOLUTIONS -positive bending moment = +200KNm -draw transformation of areas -draw strain and stress diagram
2 Compare the advantages and disadvantages of fine and coarse aggregates.
The strength of cement is determined by a number of factors.
The flexural strength (fr) of concrete measured from the bending test is always higher than the direct tensile strength (ft). In reality, the stress in the cracked part of the concrete is lower than ft. Also, failure may occur on the compressive side. Assuming NO tension softening (i.e., the stress in the cracked part stays at ft) and infinite compressive strength (i.e., compressive failure will never occur), draw the stress distribution over the depth of the beam at ultimate failure when the curvature of the section is approaching infinity. With this stress distribution, show that the upper bound of fr/ft is equal to 3. (Hint: On rotating the section, because the compressive stress can increase well beyond ft, the neutral axis will continue to shift upwards.)
Design the concrete mix according to the following conditions:Design EnvironmentPavement slab, subjected to freezingRequired design strength = 21 MPaSlab thickness = 300 mmStatistical data indicate a standard deviation of compressive strength of1.7 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification is 9.5 mL/1% air/100 kgcement.Coarse aggregate: 2 in. nominal maximum size, crushed stoneBulk oven-dry specific gravity = 2.573, absorption = 2.8,Oven-dry rodded density = 1922 kg/m3Moisture content = 1,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.540, absorption = 3.4,Moisture content = 4.5,Fineness modulus = 2.68
Use ACI method.
I need the answer as soon as possible
This course EHide blocks An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 45 mm and inner diameter of 35 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr 60 MPa (concrete). 100 kN 500 mm Select one: O FS = 1.5 O FS = 1.7 O ES- 19 5:45 PM 86°F Light rain ENG 6/18/2021
Which one of the following sentences is not correct? a. For many years, tensile strength has been measured in terms of the compressive strength. b. The modulus of rupture where the normal-weight concrete has an fc of 4000 psi is 474 psi. С. For lightweight concretes tensile strength depends largely on the porous aggregate. d. For normal weight concrete, the tensile strength depends primarily on the strength of bond between hardened cement paste and aggregate. 13:54