[2.3] Compilers can have a profound impact on the performance of an application. Assume that for a program, compiler A results in a dynamic instruction count of 1.0E9 and has an execution time of 1.1 s, while compiler B results in a dynamic instruction count of 1.2E9 and an execution time of 1.5 s. a. Find the average CPI for each program given that the processor has a clock cycle time of 1 ns. си Ans. 1.1, 1.25 b. Assume the compiled programs run on two different processors. If the execution times on the two processors are the same, how much faster is the clock of the processor running compiler A's code versus the clock of the processor running compiler B's code? Ans. 1.37

[2.3] Compilers can have a profound impact on the performance of an application. Assume that for a program, compiler A results in a dynamic instruction count of 1.0E9 and has an execution time of 1.1 s, while compiler B results in a dynamic instruction count of 1.2E9 and an execution time of 1.5 s. a. Find the average CPI for each program given that the processor has a clock cycle time of 1 ns. си Ans. 1.1, 1.25 b. Assume the compiled programs run on two different processors. If the execution times on the two processors are the same, how much faster is the clock of the processor running compiler A's code versus the clock of the processor running compiler B's code? Ans. 1.37

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

8 A computer consists of a processor and an I/O device D connected to main memory M via a shared bus with a data bus width of one word. The processor can execute a maximum of 106 instructions per second. An average instruction requires five ma- chine cycles, three of which use the memory bus. A memory read or write operation uses one machine cycle. Suppose that the processor is continuously executing "background" programs that require 95% of its instruction execution rate but not any I/O instructions. Assume that one processor cycle equals one bus cycle. Now suppose the I/O device is to be used to transfer very large blocks of data between M and D. a. If programmed I/O is used and each one-word I/O transfer requires the processor to execute two instructions, estimate the maximum I/O data-transfer rate, in words per second, possible through D. b. Estimate the same rate if DMA is used.
two different compilers are being tested on the same program for a 3.6GHz machine with three different classes of instructions: Class A,B and C, which require 1, 2 and 3 cycles respectively. the instruction count produced by the first compiler is 4 billion Class A instuctions, 1 billion class B and 4 billion class C instructions. the second compiler produces 8 billion Class A instructions, 2 billion Class B and 3 billion class C instructions. which compiler produces a higher MIPS? which compiler produces a better execution time?
dont post copied answer else sure dislike
Question 2. A program is executed for 1 sec, on a processor with a clock cycle of 100 nsec and CPI₁ = 1,5. 1. How much is the Throughput, expressed in MIPS? 2. Let us assume that, given some optimization techniques, the 30% of the program instructions is executed with CPI = 1, while the fraction of remaining instructions (70%) is executed with the same CPI. a. How much is the Speedup from the case (1) to the case (2)? b. How much is the Throughput expressed in MIPS?
1. We wish to compare the performance of two different machines: M1 and M2. The following measurements have been made on these machines: Program Time on M1 Time on M2 1 10 seconds 5 seconds 2 3 seconds 4 seconds Which machine is faster for each program, and by how much? 2. For M1 and M2 of problem 1, the following additional measurements are made:. Find the instruction execution rate (instructions per second) for each machine when running program 1. Program Instructions executed on M1 Instructions executed on M2 1 200 x 106 160 x 106 3. For M1 and M2 of problem 1, if the clock rates are 200 MHz and 300 MHz, respectively, find the CPI for program 1 on both machines using the data provided in problems 1 and 2. 4. You are going to enhance a machine, and there are two possible improvements: either make multiply instructions run four times faster than before or make memory access instructions run two times faster than before. You…
Take the accompanying project fragment for a theoretical CPU having three client registers R1, R2 and R3. Guidance Operation Instruction Size(in words) MOV R1,5000; R1- Memory[5000] MOV R2, (R1); R2 - Memory[(R1)] ADD R2, R3; MOV 6000, R2; 2 1 R2 - R2 + R3 1 Memory [6000] – R2 End Machine ends 1 Leave the clock cycles needed for different tasks alone as follows: Register to/from memory move: 3 clock cycles ADD with the two operands in register : 1 clock cycle Instruction get and unravel : 2 clock cycles for each word The absolute number of clock cycles needed to execute the program is
AziTech is considering the design of a new CPU for its new model of computer systems for 2021. It is considering choosing between two (2) CPU (CPUA and CPUB) implementationsbased on their performance. Both CPU are expected to have the same instruction set architecture. CPUA has a clock cycle time of 60 ns and CPUB has a clock cycle time of 75 ns. The same number of a particular instruction type is expected to be executed on both CPUsin order to determine which CPU would executes more instructions. CPUA is able to execute2MB of instructions in 5*106 clock cycles. CPUB executes the same number of instructions in 3*106 clock cycles.a) Using the MIPS performance metric, which of the two (2) CPU should be selected to be implemented in the new computer system. Justify your choice. b) Compute the execution time for both CPUs. Which CPU is faster?
i need the answer quickly
I need the answer as soon as possible
With regard to the performance data cited for programs v, w, x, y, and z in table 11.1, find the geometric means of the runtimes of the programs for System B and System C, using System A as the reference system. Verify that the ratios of the means are consistent with the results obtained using the other two systems as reference systems.
Microprocessor Question