2. The initial design of a simply supported beam is shown below. The architect requested the engineer to reduce beam depth by 100 mm to accommodate the client's preferred celling height. Use f'c 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Clear cover is 40 mm. Analyze as Simpiy supported beam only. 2-016 $10 (8@125, rest @ 300) SINGLY REINFORCED 450 2-016 - 2Y mm - BTYPICAL SECTION a. How many additional 16 tensile bars are required? b. What is the new spacing of stirrups near the end in mm? Round your answer to nearest safe 25 mm.

2. The initial design of a simply supported beam is shown below. The architect requested the engineer to reduce beam depth by 100 mm to accommodate the client's preferred celling height. Use f'c 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Clear cover is 40 mm. Analyze as Simpiy supported beam only. 2-016 $10 (8@125, rest @ 300) SINGLY REINFORCED 450 2-016 - 2Y mm - BTYPICAL SECTION a. How many additional 16 tensile bars are required? b. What is the new spacing of stirrups near the end in mm? Round your answer to nearest safe 25 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Check the following beams for compliance with ACI. Check the following: þMn > Mu As > As,min rebar spacing, cover requirements (cite ACI section) 2. Precast beam in parking garage: Mu = 800 k-ft %3D 18"- #3 stirrup -1 12" clear 25" 1' clear 14 ea. Nb. 8 bars f'c =6000 psi fy =60,000 psi
Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi f) what is the block shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)
| * A's O As,web As bw Steel areas: A's-2 + 14 = 308 mm² A₁=50 mm² (area of $8) Materials : C25/30 / B420C Longitudinal reinforcements A's=2 $ 14 As,web= 2 $ 12 As= 5 0 14 bw=300 mm d=670 mm d'=30 mm k₁= 0,85 k3 = 0,85 Pb=0.0205 (from table) Transverse Reinforcements $8/200 mm (2-leg stirrups) Material coefficients Ymc:1.5 (Concrete) Yms: 1,15 (Steel) Determine the reinforcement ratio and failure type of the beam As,web= 212= 226 mm² Asw=2x50=100 mm² (Total Area of two leg stirrup) A₁= 5 + 14=770 mm²
y 1 k 2" -12"- 3" 10" 10" -x For the composite area shown below, Find the centroid of the composite area. Determine ly of the composite area about its y' centroidal axis found in part (a).
Please Make a correct table and estimate ( will surely give a like if correct)
Right support: Elasticity= 374 Gpa Left support: Elasticity= 274Gpa Elongation= 9mm Answer item 1 only.
Thank youu
For a composite section attached, derive the equation for Y-bar assuming that the PNA is located in the flange of the steel beam. Hint: Balance the resultant forces through the section. Recall that Y-bar is the distance from the top of the steel flange to the PNA for any location with the PNA below the top of the steel flange.
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
a simply supported reinforced concrete beam has a Vf=140KN, determine if the beam can sustain the shear loads without shear reinforcements max aggregate = 25mm fc 3D 30 Мра fy = 400 Mpa Exposure Člass = f2 %3D ot 100 4 400 mm 8-30M
round off final answer to 4 decimal places
3-5 with clear explantion