2. Air flows at the rate of 1.5 m³/s through a horizontal pipe with a gradually reducing cross section as shown in the figure. The two cross-sections of the pipe have diameters of 400 mm and 200 mm. Take the air density as 1.2 kg/m² and assume inviscid incompressible flow. The change in pressure (P2-P1) (in kPa) between sections 1 and 2 is 200 mm Air Flow 400 mm 1.5 m/s (A) -1.28 (B) 2.56 (C) -2.13 (D) 1.28

2. Air flows at the rate of 1.5 m³/s through a horizontal pipe with a gradually reducing cross section as shown in the figure. The two cross-sections of the pipe have diameters of 400 mm and 200 mm. Take the air density as 1.2 kg/m² and assume inviscid incompressible flow. The change in pressure (P2-P1) (in kPa) between sections 1 and 2 is 200 mm Air Flow 400 mm 1.5 m/s (A) -1.28 (B) 2.56 (C) -2.13 (D) 1.28

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal pipe has a constriction in it as shown in the figure below, At point 1 the diameter is 5.0 cm, while at point 2 is only 2.5 cm. At point 1, v1 = 3.0m/s and P1 = 100 kPa. Calculate v2 and P2.
Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute pressure is 240 kPa, and water flows into the pipe at 42 kg/s. At flange (2), the total pressure measured is 190 kPa with a flow rate of 32 kg/s. At point (3) water discharges into the atmosphere at 90 kPa at a flow rate of 10 kg/s. The mass of the elbow and the water in it is 50 kg. Neglecting the momentum-flux correction factor, determine the net x- and z-force at the two flanges connecting the pipe. T0 kg/s 3 ст 32 kg/s- 10 cm 42 kg/s S cm Figure 1.2
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. May you kindly resend the answers in a different format as they appear blank??
A cylinder with a mass 0.222 kg is sliding downwards through a vertically positioned pipe. A thin oil layer exists between the cylinder and the pipe's internal surface. Centerline of the cylinder and the pipe overlap. (yoil =8044.2 N /m3 ; voil=6-106 m²/s). Find the change in the speed of cylinder in the pipe with respect to its unit displacement and the shear stress that acts upon the oil layer. A A L = 128 mm V W 73.8 mm 74 mm 0.1 mm Figure 1
A U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilled
A pipe set up is given as seen in the figure. The fluid is oil with a specific gravity of 850 kg/m³. The pressure at the exit is atmospheric pressure. The diameter at the entrance is 6.4 cm and the diameter at the exit is 2.2 cm. The volume rate of flow is given as 0.0315 m³/s and thegage pressure at the entrance is 250 kPa. Ignore weight of the fluid and the pipe. Determine the x-component of the force applied at the bolts at section 1. Assume that the atmospheric pressure is 1013 mb. 40° 2
B3
Q2: Water flow in a pipe as shown in the figure if the velocity of the fluid at section A is 1.8 m/s and at section D 1.36 m/s. Find A 1. pressure drop at section C d-300 mm d-400 mm 2. head losses at section D Take the density of water 1000 kg/m³ and viscosity of water 998 × 10-6 N.s/m² B 5 m- d-150 mm d-125 mm D
Let the pressure gradient in the pipe be 1500 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20∘C motor oil? What is the average speed through this pipe of 100∘C motor oil?
Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady, incompressible, irrational with negligible frictional effects , the effect of air column on the pressure change is negligible, the pressure can be assumed to be uniform at a given cross-section of the venturi meter and the flow is horizontal . Air is flowing through a venturi meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, take the air density to be 0.075 lbm/ft. 1. Show that the volume flow rate can be expressed as: 2(P P2) | = A, p(1 – AŽIA}) 2. Find the flow rate of the air? 12.2 psia 11.8 psia Air 2.6 in 1.8 in
Water at 20°C flows through a 11.5-cm-diameter pipe that has a 180° vertical bend, as in the figure. The total length of pipe between flanges 1 and 2 is 75 cm. When the weight flow rate is 230 N/s, p1-165 kPa and p2-134 kPa. Neglect pipe weight. Determine the magnitude of the horizontal force balance that the flanges must withstand for the flow. The magnitude of the horizontal force F=-
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.