-5 2 m /s) flows in a tube that has a In the figure shown, water (density=1000 kg/m and viscosity 1x10 diameter (d=1.9 cm) and a length L= 53 m at 1.3 kg/min. A valve was installed to the pipe. The manometers reading are given as: (h = 0.128 m, z = 0.80 m). What is the head loss coefficient of the valve?

-5 2 m /s) flows in a tube that has a In the figure shown, water (density=1000 kg/m and viscosity 1x10 diameter (d=1.9 cm) and a length L= 53 m at 1.3 kg/min. A valve was installed to the pipe. The manometers reading are given as: (h = 0.128 m, z = 0.80 m). What is the head loss coefficient of the valve?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m /s. If the pipe is cast iron of diameter 12 3. cm and the pump efficient is =0.34%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss. 32 m L = 50 m Pump
Vv
Water (kinematic viscosity, ν, = 1.14 *10-6 m2/s) flows through a piping system with a flow rate of 0.75 m3/s. The pipe is 2600 m long and 600 mm inside diameter. The pipe has four gate valves,two angle valves, one swing check valve, three standard tees through flow, and three 90o standardelbows. Calculate the following:a- The total length of the piping system.b- The Darcy friction factor if the pipe is fully smooth.
The velocity of water is measured using an orifice meter (throat diameter = 0.06m) in a 0.31-m pipeline. The measured pressure drop across the orifice is 75 kPa. The Reynolds no. at the orifice is ?
Need simple Solution with Correct answer.
As5
A petroleum liquid with (SG = 0.83), flows through the Venturi meter as shown with flowrates between 4 and 7 L/s and diameters of d1 = 0.055 m & d2 = 2 cm. Then D₁ (1) D₂ the minimum pressure difference (dp) needed to measure these flowrates is kPa.
Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asurf = 5.6 m². At the bottom of the tank there is a door inclined at an angle = 45 degrees with respect to the horizontal. The door has a length L = 0.9 m and a width w=0.8 m (out of the page). The flowrate into the tank is Q₁ (t) = 0.3 m³/s and the flowrate out is Qo(t) = 0.07 m 3/5 At time t = 0, the water has a depth ho = 2 m. The density of water is p = 1000 kg/m³. Asurf x h(t) a) Find the pressure (in kilopascals) at time t = 0 Qout
Please solve ASAP.
Given an open tank filled with oil that is discharging through a 35-meter long commercial annulus pipe as shown in figure below. Calculate the volume flowrate at point 2 when the oil surface is 5 meters from it. Neglect entrance effects take kinematic viscosity equal to 4 x10-5 m2/s. (Ro and Ri are radaii).
A 60L/s of heavy oil, p-980kg/m² and v-400mm³/s, is flowing in a 305-mm-diameter pipe. The starting elevation of pipe is z1=85m, the end elevation of pipe z,=105m, and the length of pipe l=1800m. Determine the pressure drop and power loss in the pipe.
I need the answer as soon as possible