ater (kinematic viscosity, ν, = 1.14 *10-6 m2/s) flows through a piping system with a flow rate of 0.75 m3/s. The pipe is 2600 m long and 600 mm inside diameter. The pipe has four gate valves, two angle valves, one swing check valve, three standard tees through flow, and three 90o standard elbows. Calculate the following: a- The total length of the piping system. b- The Darcy friction factor if the pipe is fully smoo

Q: For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry…

A: Given: D=8 in=0.2032 mT=65°CQ=0.01 ft3/s=0.0002831685 m3/s

Q: The pressure of point B of the hydraulic system must be 495 psig, being the expense of 758 gal/ min.…

A: Given:First Pipe diameter, d1=4 in=412ftPipe diameter after expansion, d2=6 in=612ft=0.5 ftTotal…

Q: Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows…

A: Piping systems may consist of different valves, tees, and elbows, etc. These fittings have their…

Q: A horizontal pipe with a diameter of 350 mm discharges water at the rate of 12 m2/ min and has a…

A:

Q: The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is…

A:

Q: plain the velocity and pressure behavior of the fluid through venturi. Also explain how to measure…

A: given: Explain the velocity and pressure behavior of the fluid through venturi. Also explain how to…

Q: Water flows at a rate of 2.4 ft³/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The velocity measurement observation manometer readings are 44.5 cm , 47.5 cm. The pipe diameter is…

A: Solution:

Q: In the system shown, the pipe is commercial steel, the inlet and outlet is sharp edge and the flow…

A: Flow rate, Q = 125 L/s = 0.125 m3/s Pipe diameter, D = 0.3m Pipe length, L = 30 m Elevation…

Q: The velocity measurement observation manometer readings are 44.5 cm , 48.5 cm. The pipe diameter is…

A: Given data:

Q: Consider the pipe system shown in the figure. Oil (μ = 0.3 Pa-s) flows at a rate of 20 L/s through…

A:

Q: A pilot tube was used to measure the velocity of water in a circular pipe 2 inches diameter. If the…

A: A Pitot tube is used to measure the local velocity of flow. it is highly accurate velocity measuring…

Q: What is the volumetric flow rate through at 4 inch (10 cm) diameter pipe containing chocolate milk…

A:

Q: i just need final answer The water is delivered with piping system given in the figure below. The…

A:

Q: Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows…

A:

Q: Determine the discharge for laminar flow

A: Given: pipe diameter d=0.04 m centre line velocity  =1.5 m /s I;e  centre line velocity or maximum…

Q: oil (u=0-03372 Pa.s, S6= 0.843, is flowing from the uPper to lower reservoir at a rate of oo28s…

A:

Q: coefficient of discharge=

A: Given: h1=314 mm h2= 286 mm Q=165 ltter/s A1=338.6 mm2 A2=84.6 mm2 To determine: The coefficient of…

Q: The observed pressure drop for 40°F water flowing at 16 ft/min in a 4.5-in diameter pipe is 9.68 x…

A:

Q: Benzene (u=3.95 x10-4Pa-s) at 60°C is flowing in a 24.3mm steel pipe (absolute roughness =4.6 x10-5m…

A: Answer: The pressure difference between two points 100 m apart if the pipe is horizontal: ∆P =…

Q: . What is the friction

A: Given datathe length of the pipe L = 1200ftthe diameter of the pipe d =6 in = 0.5 ftthe volumetric…

Q: fluid sulphuric acid with 75% concentation is to be pumped for 0.8 km along a 50mm density 1650…

A:

Q: The velocity measurement observation manometer readings are 44.5 cm , 47.5 cm . The pipe diameter is…

A: Ans; Discharge, Q=0.01098 m3/sec

Q: * El A Venturi meter is to be fitted to a 12.5 cm radius pipe, in which the maximum velocity is 2.44…

A:

Q: Q2/ Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced…

A:

Q: An oil is being pumped inside a pipe at rate of 5.2m/s-00. The oil density is 905 kg/m3 and the…

A: Reynolds number Re = ρvDμρ= densityv = velocity D = diameterμ= viscosity

Q: Water discharge flow rate of 0.001 m3/s is delivered through the 30 mm cast iron pipe? €=0.15…

A: Calculate the velocity of the water into the cast iron pipe. Q=Av0.001 m3/s=π40.030 m2vv=1.414 m/s…

Q: Calculate the volume flow of water (SG=1) through the pipe.

A: GivenP1=565 kPaD=80mmt=2.8 mm At exitZ2=3.65md=35mmSG=1a=0.000962 m2

Q: The velocity measurement observation manometer readings are 44.5 cm , 49 cm . The pipe diameter is…

A: Solution:

Q: Problems: two vessels are connected by a pipe of the diameter of d=100 mm and length of =12 m, made…

A:

Q: A Pitot probe is mounted in a 25 mm inner diameter pipe at a location where the local velocity is…

A:

Q: Water flows at a rate of 65 Li/min in a steel pipe of 45 mm diameter, K = 0.045x10-3 m, μ = 0.001…

A:

Q: Consider the pipe system shown in the figure. Oil (μ = 0.3 Pa-s) flows at a rate of 20 L/s through…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: A pipeline has the following data at its two section A and B Item Section - A  Section - B Diameter…

A: water flowing through point B to A at point B, D2 =0.45m,  Z2 =16m, P2 =30KPa, α2 =1.25 at point A,…

Q: 8. Ahorizontal pipe has a non-negligible expansion (K, = (1 Asmall Atarge as shown in the figure.…

A:

Q: What are the flow Q and the velocity V when total head loss is H = 25 m?

A: Total head loss,(Hloss)=25 m. Kentrance=1Kglove valve=10Kelbow=0.9Kexit=1D=20mmf=0.02L=9m. Determine…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.