Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolutepressure is 240 kPa, and water flows into the pipe at 42 kg/s. At flange (2), the total pressuremeasured is 190 kPa with a flow rate of 32 kg/s. At point (3) water discharges into theatmosphere at 90 kPa at a flow rate of 10 kg/s. The mass of the elbow and the water in it is 50kg. Neglecting the momentum-flux correction factor, determine the net x- and z-force at the twoflanges connecting the pipe.T0 kg/s3 ст32 kg/s-10 cm42 kg/s S cmFigure 1.2

Answered: Image /qna-images/answer/8b77ae3c-ef77-4f51-8638-d851406a5d24.jpg

Answered: Water is flowing through a U-section…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4 identical jets spaced equally around the rim of a disc. Water enters though a hollow shaft and then flows radially out to the jets. The nozzle of the jet has a diameter D of 0.3 cm and makes an angle a = I (3 with the horizontal plane of the disc(See figure). The jets are oriented so that v2r=0. If the total flowrate Q=50 mL/s and the disc has radius R= 7.5 cm, determine the torque in dyne-cm required to keep the disc from rotating. Water jet R. Water flows radially inside dise to jet Water in View from top View from side
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
0.95 m3/sec flow rate of water flows downwards in a pipe as shown in figure. If the pressures at points 1 and 2 are to be equal. Determine the diameter of the pipe at point 2.The velocity at point 1 is 6.5 m/sec and the diameter of pipe at point 1 is 330 mm. The height between point 1 and point 2 is 2.8 m?
Towards the inside of a cylindrical tank with diameter: D = 24 m, water flows through a tube 1 with a velocity v1 = 20 m / s and exits through tubes 2 and 3 with velocities v2 = 8 m / s and v3 = 10 m / s respectively. At 4 there is a vent valve open to the air from the atmosphere. (a) What is the speed with which the level rises of water in the tank? (b) what is the average velocity of the air flow at valve 4? assuming air is incompressible. Assume the following pipe diameters: D1 = 3 m, D2 = 2 m, D3 = 2.5 m, D4 = 2 m, consider that the density of water is: ρw = 103 kg / m3 , and the density of air is: ρa = 1.2 kg / m3
A pitot-static tube is used to measure the air flow at the centre of a 400mm diameter building ventilation duct. If the height measured on the attached manometer is 10mm and the density of the manometer fluid is 1000 kg/m3, determine the volume flow rate in the duct. Assume that the density of air is 1.2 kg/m3.
Starting from the Bernoulli equation and conservation of mass equation, derive the flow rate equation for the pipe shown in Figure Q2. Then, determine the magnitude of the flow rate.
An incompressible fluid flows steadily through two pipes of diameter 0.15 m and 0.2 m which combine to discharge in a pipe of 0.3 diameter. If the average velocities in the 0.15 m and 0.2 m diameter pipes are 2 m/s and 3 m/s respectively, then find the average velocity in the 0.3 m diameter pipe.
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
3. A pipe with varying cross-sectional areas is set up vertically as shown in the drawing. Water enters the pipe from the top wider end at a speed of 300 cm/s. Calculate (a) the mass flow rate of water (the amount of mass entering/exiting the piper every second) and (b) the water pressure at the bottom narrower end section of the piper. (Density of water is p = 1000 kg/m2 1.00 g/cm')) P 1.20x10 Pa 10.0 cm h=4.00 m 2.50 cm2 P= ?
Question Water enters the horizontal circular nozzle with the inlet diameter of 5 in. At the inlet section, fluid has uniformly distributed velocity of 20 ft/s and pressure of 85 psi. The water exits from the nozzle into the atmosphere at the outlet section where the uniformly distributed velocity is 100 ft/s. Determine the axial component of the anchoring force required to hold the contraction in place. Answer The axial component of the anchoring force required to hold the contraction in place is lbf.
A 75-mm diameter pipe is connected to a 100-mm diameter pipe. If the velocity of flow in the 75-mm pipe is 2 m/s, what is the velocity of flow in the 100-mm pipe? What is the flow rate in the 75-mm pipe in m^3/s?
Consider the piping system shown in the figure. The speed of water flowing through the 4-in diameter segment of the piping system is 3 ft/s. What is the volumetric flow rate of water in the piping system? Express the volumetric flow rate in ft3/s, gpm, and L/s. For the case of steady flow of water through the piping system, what is the speed of water in the 3-in diameter segment?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS