Water with density Pwater = 1000 kg/m³ flows through a pipe, composed of two reduced in size sections, as shown on the figure. The two sections are linked with a flange connection, and the corresponding diameters are D, = 8 cm and D, = 5 cm. If the velocity in cross-section 1 is v, = 5 m/s, and the readings of the connected liquid manometer is h = 60 cm, determine the reaction force acting over the flange connection. The manometric fluid is mercury, with density Pa-101kPa %3D %3D Mercury Pmercury = 13600 kg/m³.

Water with density Pwater = 1000 kg/m³ flows through a pipe, composed of two reduced in size sections, as shown on the figure. The two sections are linked with a flange connection, and the corresponding diameters are D, = 8 cm and D, = 5 cm. If the velocity in cross-section 1 is v, = 5 m/s, and the readings of the connected liquid manometer is h = 60 cm, determine the reaction force acting over the flange connection. The manometric fluid is mercury, with density Pa-101kPa %3D %3D Mercury Pmercury = 13600 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the expanding pipe system with circular cross section given in the figure, the fluid moves from point A to point B with a flow rate of 0.2 m'/s. Since the pressure height at point A is 7 m and energy loss during movement is 0.1 m, find the pressure height at point B. Draw the energy line of the system on the figure.
Time left 0:04:15 H R (m) Н (m) В (т) Sg 2.5 7.8 M R Fresh 2.5 1.10 Water Determine the magnitude of the total resultant pressure force FR acting on the half of a semi- cylindrical bottom surface mn of the tank shown in the figure. The radius of curvature is R (m). A head H (m) is above the surface Om. The width of the tank B (m). The surface of water is exposed to the atmosphere. Then, select an answer [FR = KN] O a. [954.32] O b. [712.35] с. [672.13] o d. [897.81]
Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure difference p between the 2 manometers. We can assume that the energy losses by friction are negligible, and that there are only singular energy losses (be careful to identify ALL the singularities). The pump adds an energy of HP = 10 m to the system. "GATE VALVE" P2 OUVERTURE COMPLÈTE do = 150 mm Q = 50 L/s • 2) 2 m Q = 50 L/s COUDES À POMPE RAYONS COURTS do = 150 mm (Hp = 10 m)
Water flows through a circular pipe with a 180° elbow and exits to the atmosphere through a nozzle as shown in the figure. The diameter of the pipe is 300mm and the diameter of the nozzle exit is 160mm. The density of water is 1000kg/m3. The pressure gauge at the front of the pipe (section 1) reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint at section 1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm and the weight of the elbow and the water is 100N. Z1 is 0.3 m.
simple answer no need to explain
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
Water is stored in a pressurised container at a height HT= 8.4 m. It then moves through a horizontal pipe which has a height HP= 0.2 m off the ground. A fault occurs, and the water in the pipe is ejected vertically out of a valve, as shown in the figure. The jet reaches a maximum height Hj off the ground. The density of water is ρ=1000 kg/m^3, and the gauge pressure in the tank is pT= 45 kPa.a) Find the maximum height of the jet, Hj (in metres)b) Find the velocity at which the jet leaves the pipe (in m/s)
Water with density Pwater = 1000 kg/m³, is transported in 30° circular pipe, inclined at an angle of 30°, relative to the horizontal plane. The readings of the connected liquid manometer, as shown on the figure, is h = 12 cm. The manometric fluid used is a mercury with density Pmercury = 13600 kg/m³. The temperature of both fluids is equal and is t = 20 °C. Find the pressure difference Ap = p, – p, in the both cross- h sections 1 and 2. ****
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
The velocity profile of a liquid flows through the z direction of the vertical tube (figure right) with the radius ro is given as; r 1 dp Vz = (r² – r3) 2µ dz Specify the maximum velocity and derive an expression for the average velocity.
Water flowing at 1.0 ft/s in a pipe passes into a constriction where area is one-tenth the normal pipe area. What is the decrease in water pressure in the constriction? The weight density of water is 62.4 lbs/ft3.