2 - The rigid bar ABC in Figure is pinned Steel Aluminum at B and attached to the two vertical L = 0.5 m L= 1.5 m rods. Initially, the bar is horizontal and the vertical rods are stress-free. A = 500 mm? A = 1500 mm? Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC. (30 Points) Steel Aluminum E = 200 x 10° N/m2 a = 11.7 um/(m- °C) E = 70 x 10° N/m2 a = 23 um/(m-°C) B A 0.6 m 1.2 m

2 - The rigid bar ABC in Figure is pinned Steel Aluminum at B and attached to the two vertical L = 0.5 m L= 1.5 m rods. Initially, the bar is horizontal and the vertical rods are stress-free. A = 500 mm? A = 1500 mm? Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC. (30 Points) Steel Aluminum E = 200 x 10° N/m2 a = 11.7 um/(m- °C) E = 70 x 10° N/m2 a = 23 um/(m-°C) B A 0.6 m 1.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel rod having a length of 50m is suspended vertically from one end. It supports a tensile load of P = 250 kN at the lower end. The unit weight of the steel is 7850 kg/m^3. The allowable tensile stress for steel is 140 MPa. Use E = 200 GPa. Determine the total deformation of the steel rod.
The stresses on an element are o, = -270 psi and o, = -540 psi. y Oy Find the maximum shear stresses (in psi) on the element. (Assume t. = 0. Use the sign convention for shear stresses.) ху (Tmax)x1 = psi (Tmaxlyı = psi (Tmaxl21 = psi
2.75 A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at –20°C, find the minimum allowable diameter of the rod. Use a = 11.7 × 10–6/°C and E = 200 GPa. %3D
The steel bars are firmly attached to rigid supports. Initially the temperature is 840F. Determine the stress in bars AC and CB when the temperature becomes -600F. Use E = 29 x 106 psi and α = 6.50 x 10-6/ 0F.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
13
Question 2) Knowing that a 0.02-in. gap exists when the temperature is 75 °F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. Bronze A = 2.4 in² E = 15 x 10 psi a = 12 x 10-6/°F -18 in.- Aluminum A = 2.8 in² E = 10.6 x 105 psi a = 12.9 x 10-6/°F