Answered: Steel bar of cross-section 550mm2 is…

Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The uniform beam of weight W is to be supported by the two rods, the lower ends of which were…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 90 MPa and S, =…

A: Given data in question Normal stresses as compressive and tensile Angle No shearing stress To find…

Q: q1=150 Mpa, q2=40 MPa Calculate the stresses σx,σy,σz and deformation εz1,εz2 in the z direction.

A: Elastik cisim 1 q1=150 Mpa, σz = -150 Mpaσx,σy = 0∈z = σzE = 150300×103∈z =5×10-4∈x =∈y =…

Q: 1. The thermal extension of any member depends on the expanslon coefficient of this member. 2. The…

A: We only provide solution to first three answers, kindly resubmit the remaining parts for required…

Q: bar shown if the temperature increas supports are unyielding and that the buckling. 4 Aluminum A =…

Q: The state of stress at a point is given by 0=x²y² + 30, 0₁y = x² + y² + 15. o = xy²2 + 30, T₁y =…

A: First we summarise the given data : To find : Determine the body force distribution at the point (…

Q: A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of…

Q: A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂…

A: G = 10.93 MPaP = 13 kN or 13000 N

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

Q: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a…

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

Q: An elastic bar of length L, uniform cross-sectional area A, coefficient of thermal expansion a , and…

A: Solution; The axial stress diagram; σ varies with ∆T and does not depends upon the length of bar.

Q: A rigid bar of negligible weight is supported as shown. If P= 80 KN, compute the temperature change…

A: Tensile strength is defined as the ability of a material to resist a force that tends to pull it…

Q: Aluminum D=20mm Steel 200kN 200KN Bronze D=25mm D=28mm 150kN

Q: 1. Given that the value of P on the figure below is equal to 15 kN which is applied to the…

A: To Determine Stress in each rod segment.

Q: . What is the normal strain in the y-direction? What is the normal strain in the n-direction?in…

A: All Data is given in the figureNeed to find1- the normal strain in the y-direction2- the normal…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: Two vertical rods, one of steel and the other of copper, with cross-sectional areas 500 mm² and 1000…

A: Cross sectional area of steel (As) = 500 mm2Cross sectional area of copper (Ac) = 1000 mm2Total load…

Q: Two vertical rods, one of steel and the other of copper, with cross-sectional areas 500 mm² and 1000…

A: Cross sectional area of steel (As) = 500 mm2Cross sectional area of copper (Ac) = 1000 mm2Total load…

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

A: ASKED: To determine the stress in bars AC and AB. Given, Initial temperature (T1) = 84 oF Final…

Q: The rigid bar AC is pinned at A and attached to bars DB and CE as shown in the figure. The weight of…

A: Given data in question Weight of beam Length of bars Area Elasticity modulus Coefficient of…

Q: A state of stress is specified in the figure shown below. Determine the Normal stress (mPa) on the…

A: The normal stress on vertical plane, Px=-63MPaThe normal stress on horizontal plane, Py=-80MPaThe…

Q: For the figure shown, increasing temperature causes compressive .stress in the steel rod

A: When there is an increase in temperature steel rod tends to expand . But due to the presence of a…

Q: 80.7 MPa В. = 71.15" = -18.85 32.7 MPa 77.5 MPа C. = 67.91* -22.09* 25.5 MPa 84.7 MPa D. = 75.11"

Q: 2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in…

Q: Q-A uniform prismatic circular bar made up of rigid material is subjected to a tensile force of 5000…

A: Tensile force F=5000 N Diameter of cross-section d=7 mm It is needed to find the stress and strain…

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

Q: The rigid bar is supported by a pin at A and two metal wires,each having a diameter of 4mm.The…

Q: The curvature of the beam at the mid-span

A: Given, Equation of deformation is derived to be, y= x3-xL (shown in figure)Determine the curvature…

Q: The rigid bar of negligible weight is supported as shown in the figure. If W = 104 kN, compute the…

A: The change in the length of member with respect to its original length is due to various reasons…

Q: The nut on a bolt is tightened by applying a force of P = 18 lb to the end of a wrench at a distance…

Q: Knowing that a 0.03-in. gap exists when the temperature is 85 °F, determine the temperature at which…

A: Given : Determine the temp. at which the normal stress in the aluminum bar will be equal to 11…

Q: Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the…

A: Given ;

Q: 9-10 Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the…

A: you can also use σx+σy=σx′+σy′ . if you one of the required stressesif you have any doubts please…

Q: The rigid bar of ABCD of negligible weight is supported hinge at A, steel rod at B and bronze rod at…

Question

Steel bar of cross-section 550mm² is acted upon by the forces shown in figure. For steel, E = 200GPa.

Compute the stress in BC
Compute deformation of AB
Compute the total elongation of the assembly.

A
B
C
D
50 kN
15 kN
10 kN
45 kN
0.6 m
m
-1.25 m-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The rectangular steel plate in the figure is forced by the forces given at the A and B points. a) Size the cross section according to the most economical section ratio a / b = 1/2. b) Calculate the amount of deformation occurring in the rod in this case. The yield stress of the steel plate can be taken as 400 Mpa, the modulus of elasticity 2.10 ^ 5 Mpa, the safety coefficient of the design can be taken as 2. F = 3kN L = 1.5m
9. The initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and BD. Undeformed Deformed A B D 2.0 mm 2.015 mm C 1.995 mm
The state of stress at a certain point in a stressed body is as shown in the figure. Normal stress in x-direction is 80 MPa (Tensile) and in y-direction is 40 MPa (Compressive). The radius of the Mohr's circle for this state of stress will be O, = 40 MPa O, = 80 MPa + Ox = 80 MPa Oy = 40 MPa (а) 60 MPа (b) 40 MPa (c) 20 MPa (d) 10 MPa
A steel rod having a length of 50m is suspended vertically from one end. It supports a tensile load of P = 250 kN at the lower end. The unit weight of the steel is 7850 kg/m^3. The allowable tensile stress for steel is 140 MPa. Use E = 200 GPa. Determine the total deformation of the steel rod.
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
thanks
Triangular wedges stresses.
P = 300N ، a=140mm , b=240mm , d=26mm
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D