15.1Assuming that only CaSO3 is produced, calculate the daily production rate (in tons/day) of a 55%-solids sludge from a 90%-efficient lime (CaO) FGD system on a 600-MW power plant burning a 3.5%-sulfur coal. The plant has a thermal efficiency of 35% and the coal has a heating value of 12,000 Btu/lb. Assume that the lime is 98% CaO and 2% inert compounds, and that its feed ratio (actual to theoretical) is 1.03 Help me with this one: Rework Problem 15.1 using lime (CaO) as the reagent. Assume the lime is 98% CaO and 2% inert compounds, and that its feed ratio (actual to theoretical) is 1.03. Answer: 1286 tons/day of sludge

Q: P.C. V, X, S S.C. Qs Xg, Sp Act. Sludge Basin RAS Q, S, Xp WAS Qw, Sun Xw

A: 1. V=5222 m3   2. Qw=121.8 m3/day   3. Qe=25798.2 m3/day   4. t=4.8 hours

Q: Q2: (12.5 Marks) Two-stage softening: A water with the ionic characteristics shown below is to be…

A: Step 1: 1. Draw the treatment units scheme The typical treatment units in a two-stage softening…

Q: 1. The required reactor detention time, 0. 2. The reactor basin volume, V, in m³. 3. The net waste…

A:

Q: A water contains a suspended solids concentration of 10.30 mg · L−1. Coagulation reduces this to 1.0…

A:

Q: Some waste has a five-day BOD at 20 °C equal to 210 mg/L and an ultimate OD of 350 mg/L. Find the…

A: Given data :BOD at 20oC is (L) = 210mg/LUltimate BOD at 20oC is (L) = 350mg/L

Q: There is a sewage sludge with volume containing a certain moisture content p, (percent). What will…

A:

Q: Using Rihet equation, estimate aeration tank Volume (V) based on the following conditions:…

A: GIVEN- Saturation constant (Ks) = 80 mg/L microbial decay coefficient (kd) =0.15/d maximum specific…

Q: 6. A tertiary treatment plant treats a municipal secondary effluent and is to employ fixed-bed…

A: Reference : Environmental Engineering, Waste water treatment plant. Given : Flow, COD, Contact time…

Q: The solids content of a stream water sample is to be determined. The total solids content is…

A:

Q: An MSW (Municipal Solid Waste) sample weighs 5 kg. Total energy content of the waste sample…

A: An MSW (Municipal Solid Waste) sample weighs 5 kg.Total energy content of the waste sample collected…

Q: 9. Improperly stored industrial waste results in the discharge of chlorobenzene (C6H5CI) into…

A: The hydraulic gradient (i) is the change in head over the change in distance. In this case, the head…

Q: 1) Estimate the biomass concentration in a CSTR aeration tank with the following operating…

A:

Q: quantity of water to be treated is 2 MGD. i Estimate the total hardness, carbonate hardness and…

A: Given:- quantity of water treated =12MGD Lime and soda process To find:- a)total hardness ,carbonate…

Q: Microbial growth in an activated sludge system can be described by the Monod model. If the maximum…

A: µ=specific growth rate = .6 day-1   µmax=maximum value of μ = 1.2 day-1   KS=saturation constant =…

Q: Consider an activated sludge WWTP (wastewater treatment plant). Influent comes in at 28 million…

A: As per guidelines, we are supposed to answer only first 3 sub-parts. Kindly repost other parts in…

Q: An ion exchange softener of 5 m3 volume is used to treat the raw water for a community. The…

A:

Q: A complete-mixed activated sludge process is to be designed to treat 5.0 MGD of primary effluent…

A: Flow rate= 5 MGD  Primary effluent BOD5 = 180 mg/ L

Q: Biomass and substrate mass balance equations can be merged giving QwXR/VX=Y/X (Qo/V) (So-S)-kd (i)…

A: We know that Hydraulic retention time and Solid retention time is as follows:

Q: .40. A solution is known to contain 50 g/m³ of CH3(CH₂),COOH and 42 g/m³ of NH3-N. Determine the…

A:

Q: A Granulated Activated Carbon (GAC) adsorption laboratory column 10cm in diameter and 3m deep, is…

A: Since we answer three sub-parts at a time, so we will answer the first three sub-parts . Please…

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.