Answered: 14 The brass bar shown is loaded…

14 The brass bar shown is loaded axially in compression so that the maximum stress induced is 125 MPa. Calculate the total change in length (E = 100 GPa). 20 mm 70 mm + [=] 90 mm 30 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the allowable tensile stress for the bar is (ot)allow = 20 ksi, and the allowable shear stress for the pin is Tallow = 11.6 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t = 1/4 in. and w = 2 in. (Figure 1) Figure w/2 [w/2 P 1 of 1 > Part A Determine the diameter of the pin so that the load P will be a maximum. Express your answer to three significant figures and include appropriate units. d= Submit Part B P = Submit μA Value Request Answer What is this maximum value for P? Express your answer to three significant figures and include appropriate units. li μA Provide Feedback Value Units Request Answer ? Units ?
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
F=17000000
The wood column is pinned at its base and top. Take E= 10 GPa and or = 15 MPa. (Figure 1) Figure 150 mm" 25 mm 25 mm 75 mm 75 mm 1 of 1 Part A If the eccentric force P = 11.8 kN is applied to the column, determine the maximum normal stress. Express your answer to three significant figures and include the appropriate units. TIGB = Submit Part B Value Request Answer Submit Units If the eccentric force P = 11.8 kN is applied to the column, investigate whether the column is adequate to support this loading without buckling or yielding. ? O The column is adequate to support this loading without buckling or yielding. O The column is inadequate to support this loading without buckling or yielding. Request Answer
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. parameter value units L. 450 mm L2 300 mm d₁ 40 mm d2 30 mm P 40 KN L1 d₁ P B CC 030 BY NO SA 2021 Cathy Zupke P L2 D U MPa MPa The stress in AB σAB= The stress in CD and EF: σCD = σEF= E F
Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure. 200 mm = 30 mm 5000 N 5000 N r= 15 mm
4. Show your complete solution.
Ineed answer within 20 minutes please please with my best wishes
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.
Pls box ur answer thx u
Rank the normal stress in each section of the bar. Rank the values of normal stress from largest (largest tensile stress) to smallest (largest compressive stress). Use AB for segment AB, BC for segment BC, and CD for segment CD.
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?