*13-96. The spring-held follower AB has a mass of 0.5 kgand moves back and forth as its end rolls on the contouredsurface of the cam, where r = 0.15 mand z = (0.02 cos 20) m.If the cam is rotating at a constant rate of 30 rad/s,determine the force component F, at the end A of thefollower when e = 30°. The spring is uncompressed whene = 90°. Neglect friction at the bearing C.z = (0.02 cos 20) m0.15 me = 30 rad/sk = 1000 N/m

The displacement function is Differentiate the above equation with time, Again, differentiate the…

Answered: *13-96. The spring-held follower AB has…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F17-16. The 20-kg sphere rolls down the inclined plane without slipping. Determine the angular acceleration of the sphere and the acceleration of its mass center. 0.15 m 30°
F17-14. The 100-kg cylinder rolls without slipping on the horizontal plane. Determine the acceleration of its mass center and its angular acceleration. 0.3 m P = 200 N
This is a dynamics question. Answer: vB = 24.1 m/s
R18–7. The system consists of a 20-lb disk A, 4-lb slender rod BC, and a 1-lb smooth collar C. If the disk rolls without slipping, determine the velocity of the collar at the instant the rod becomes horizontal, i.e., e = 0°. The system is released from rest when 0 = 45°. 3 ft 0.8 ft
*18-64. The door is made from one piece, whose ends move along the horizontal and vertical tracks. If the door is in the open position, 6 = 0°, and then released, determine the speed at which its end A strikes the stop at C. Assume the door is a 180-lb thin plate having a width of 10 ft. 5 ft 3 ft
The 2.5-kgkg rod ACBACB supports the two 4.1-kgkg disks at its ends. If both disks are given a clockwise angular velocity (ωA)1=(ωB)1=4.6rad/s(ωA)1=(ωB)1=4.6rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins AA and BB. Motion is in the horizontal plane. Neglect friction at pin CC.
*18–4. The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2 N•m/rad, and the wheel is rotated until the torque M = 25 N • m is developed, determine the maximum angular velocity of the wheel if it is released from rest. 0.5 m M
Example: 18-63. The uniform 80-lb garage door is guided at its ends on the track. If it is released from rest at 0 = 0º, determine the door's angular velocity at the instant = 30°. The spring is originally stretched 1 ft when the door is held open, 0 = 0°. Assume the door can be treated as a thin plate, and there is a spring and pulley system on each of the two sides of the door. Solution: 8 ft A 8 ft B k = 9 lb/ft
16-90. Due to slipping, points A and B on the rim of the disk have the velocities shown. Determine the velocities of the center point C and point D at this instant. Vy = 10 ft/s B 0.8 ft 45°. CN30° VA = 5 ft/s
1- The bucket is hoisted by the rope that warps around a drum wheel. If the angular displacement of the wheel is 9 =(3t2-7t) rad, where t is in seconds, determine the velocity and acceleration of the bucket when t= 5 sec
16-34. For a short time a motor of the random-orbit sander drives the gear A with an angular velocity of VA = 40(t3 + 6t) rad/s, where t is in seconds. This gear is connected to gear B, which is fixed connected to the shaft CD. The end of this shaft is connected to the eccentric spindle EF and pad P, which causes the pad to orbit around shaft CD at a radius of 15 mm. Determine the magnitudes of the velocity and the tangential and normal components of acceleration of the spindle EF when t = 2 s after starting from rest. B D 40 mm 10 mm A -15 mm -Ε F WA P
13-85. The spring-held follower AB has a weight of 0.75 lb and moves back and forth as its end rolls on the contoured surface of the cam, where r= 0.2 ft and z = (0.1 sin 20) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force at the end A of the follower when 0 = 45°. In this position the spring is compressed 0.4 ft. Neglect friction at the bearing C. z = 0.1 sin 20 0.2 ft B ở = 6 rad/s A k= 12 lb/ft

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS