18-41. The spool has a mass of 20 kg and a radius ofgyration of ko = 160 mm. If the 15-kg block A is releasedfrom rest, determine the distance the block must fall inorder for the spool to have an angular velocity w = 8 rad/s.Also, what is the tension in the cord while the block is inmotion? Neglect the mass of the cord.200 mm

Given that: The mass of the spool m=20 kg. The radius of gyration is K0=160 mm The angular velocity…

Answered: 18-41. The spool has a mass of 20 kg…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The spool has a mass of 50 kg and a radius of gyration ko = 0.280 m. If the 20-kg block is traveling downward at a speed of 4 m/s, determine the total kinetic energy of the system at this instant. 0.3 m 0.2 m
The system is made up of the 1-m, 6.5-kg uniform rod AB and the two uniform disks (each of 0.19 m radius and 1.5 kg mass). If the system is released from rest when = 80°, when rod AB has just become horizontal, determine the coefficient C in the expression Cw² which is the kinetic energy of rod AB at this instant. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. AB' Take g= 9.81 m/s². A-L B m Your Answer: Answer
18-9. The disk, which has a mass of 20 kg, is subjected to the couple moment of M = (20 + 4) N• m, where e is in radians. If it starts from rest, determine its angular velocity when it has made two revolutions. 300 mm м
R19-1. The cable is subjected to a force of P = (10r) Ib. where t is in seconds. Determine the angular velocity of the spool 3 s after Pis applied, starting from rest. The spool has a weight of 150 lb and a radius of gyration of 1.25 ft about its center, O. P= (10) lb 1 ft
18-50. The compound disk pulley consists of a hub and attached outer rim. If it has a mass of 3 kg and a radius of gyration of ke = 45 mm, determine the speed of block A after A descends 0.2 m from rest. Blocks A and B each have a mass of 2 kg. Neglect the mass of the cords. 100 mm 30 mm
The uniform slender bar has a mass of 7 kg. If the spring is unstretched when Ⓒ = 0º, determine the magnitude of the reaction force exerted on the bar by pin A when = 45°, if at this instant w = 7 rad/s. The spring stiffness is k = 150 N/m. A 800 mm k = 150 N/m B
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
*19-8. The assembly weighs 10 lb and has a radius of gyration kg = 0.6 ft about its center of mass G. The kinetic energy of the assembly is 31 ft - Ib when it is in the position shown. If it rolls counterclockwise on the surface without slipping, determine its linear momentum at this instant. 0.8 ft 1 ft 1ft
18–37. The spool has a mass of 20 kg and a radius of gyration of 200 mm ko = 160 mm. If the 15-kg block A is released from rest, determine the velocity of the block when it descends 600 mm. A
The uniform 80 kg slender rod is at rest in the position shown when P = 450 N is applied. Determine the value of angular velocity, w2 the rod if L1 = 5.5 m and L2 = 6.5 m. A L L2 L1 B
The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 354 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 3.2 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². F 0 Your Answer: Answer
The 21-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.5 m. If it is subjected to the constant moment M = 78 N•m and is released from rest from the position as shown, determine its angular velocity w (in rad/s) when it has rotated 45°. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s2. `L MV Your Answer: Answer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS