18-15. The pendulum consists of a 10-kg uniform disk anda 3-kg uniform slender rod. If it is released from rest in theposition shown, determine its angular velocity when it rotatesclockwise 90°.0.8 m* M = 30 N •m2 m

Answered: Image /qna-images/answer/69c1b503-14c8-4827-8aa9-5b1c1a1cb19a.jpg

Answered: 18-15. The pendulum consists of a 10-kg…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 10-kg uniform cylinder is pin supported at its center O. The square isacted upon by a constant force F = 10N and a constant couple moment M = 10 Nm.If the disk starts from rest, determine1) The reactions at the pin O and the angular acceleration of the disk2) The number of revolutions it must take to attain an angular velocity of 10 rad/s
f cion A force of P = 20 N is applied to the cable, which causes a 175 kg of radius of Gyration KG = 0.42m reel to turn without slipping on the 2 rollers A and B of each 18 kg and radius of 0.1m. P 30° 250 mm OG 500 mm AO OB -400 mm- Calculate the work done by the 20N for 2 revolutions. (J) Determine the angular velocity of the reel after it has rotated 2 revolutions starting from rest. (rad/s) Calculate the Kinetic energy of roller A after the reel rotated 2 revolutions starting from rest. (J) Choose... 7.952 1.88 32.2 3.14 1.98 16.34 20 3.66 62.831 Choose... Choose... Choose... 52 8:44 AM MM
The racing vehicle has a mass of 750 kg and center of mass in G. If there is no slippage, determinate the normal reaction, in Newtons, presented on each of the front wheels in A, when an acceleration of a = 6.4 m/s².
The 10 kg wheel has a radius of gyration about its center O of ko = 300 mm. When the wheel is subjected to the couple moment, it slips as it rolls. Determine the angular acceleration of the wheel and the acceleration of the wheel's center O. The coefficient of kinetic friction between the wheel and the plane is = 0.2. (Figure 1) Figure M 100 N m < 1 of 1 0.4 m Part A Determine the angular acceleration of the wheel. Express your answer to three significant figures and include the appropriate units. α = Submit ■ Part B ao = μÅ X Incorrect; Try Again Value Submit Previous Answers Request Answer Determine the acceleration of the wheel's center O. Express your answer to three significant figures and include the appropriate units. μA Units Value X Incorrect; Try Again Units ? Previous Answers Request Answer ? Units input for part B
SOLVE USING PRINCIPLE OF WORK AND ENERGY
The 45-kg reel has a radius of gyration about its center O of ko = 220 mm. If it is released from rest, determine the total external work done to it when its center O has traveled 6.6 m down the smooth inclined plane (with angle = 35°). Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s². 0.4 m 0.2 m²
The uniform 50-kg sphere has radius r = 0.2 m and is welded to the center of the uniform 30-kg shaft as shown. When a constant couple moment M is applied to the shaft, its angular velocity reaches 74 rad/s after 4 s. Determine the magnitude of the moment M. Write your answer in N.m but do not write the units. M R= 0.1 m Taylor e m Te am Answer: Answer
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The system is made up of the 1-m, 6.7-kg uniform rod AB and the two uniform disks (each of 0.10 m radius and 2.2 kg mass). If the system is released from rest when 0- 55", when rod AB has just become horizontal, determine the angular velocity of rod ABin rad/s. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g= 9.81 m/s?. 1m
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 354 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 3.2 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². F 0 Your Answer: Answer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

18-15. The pendulum consists of a 10-kg uniform disk and a 3-kg uniform slender rod. If it is released from rest in the position shown, determine its angular velocity when it rotates clockwise 90°. 0.8 m * M = 30 N •m 2 m