L ୮ (b) Procedure (c) Expected result - 13- 3. Shastri recalled reading that for an ideal transformer, "the ratio of the primary voltage to the secondary voltage is equal to the ratio of the secondary current to the primary current." Plan and design an experiment to investigate whether the statement above is true. (8) • With the aid of a fully labelled circuit diagram, describe a procedure which can be used to investigate whether the statement is true. The circuit diagram must include the following components: A variable AC voltage supply • AC voltmeters • AC ammeters A transformer with adjustable turns ratio Connecting wires • ° A load resistor

L ୮ (b) Procedure (c) Expected result - 13- 3. Shastri recalled reading that for an ideal transformer, "the ratio of the primary voltage to the secondary voltage is equal to the ratio of the secondary current to the primary current." Plan and design an experiment to investigate whether the statement above is true. (8) • With the aid of a fully labelled circuit diagram, describe a procedure which can be used to investigate whether the statement is true. The circuit diagram must include the following components: A variable AC voltage supply • AC voltmeters • AC ammeters A transformer with adjustable turns ratio Connecting wires • ° A load resistor

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter23: Electromagnetic Induction, Ac Circuits, And Electrical Technologies

Section: Chapter Questions

Problem 77PE: (a) Use the exact exponential treatment to find how much time is required to bring the current...

See similar textbooks

Similar questions

In Figure OQ32.4, the switch is left in position a for a long lime interval and is then quickly thrown to position b. Rank the magnitudes of the voltages across the Four circuit elements a short time thereafter from the largest to the smallest.
Construct Your Own Problem Consider a double transformer to be used to create very large voltages. The device consists of two stages. The first is a transformer that produces a much larger output voltage than its input. The Output of the first transformer is used as input to a second transformer that further increases the voltage. Construct a problem in which you calculate the output voltage of the final stage based on the input voltage of the first Stage and the number of turns or loops in bath parts of both transformers (four coils in all). Also calculate the maximum output current of the final stage based on the input current. Discuss the possibility of power losses in the devices and the effect on the output current and power.
The average ac current delivered to a circuit is zero. Despite this, power is dissipated in the circuit. Explain.
(a) The plug-in transformer for a laptop computer puts out 7.50 V and can supply a maximum current of 2.00 A. What is the maximum input current if the input voltage is 240 V? Assume 100% ef?ciency. (b) If the actual efficiency is less man 100%, would the input current need to be greater or smaller? Explain.
The current in the RL circuit shown here increases to 40% of its steady-state value in 2.0 s. What is the time constant of the circuit?
Apply the loop rule to Loop afedcba in die preceding problem.
Construct Your Own Problem Consider the use of an inductor in series with a computer operating on 60 Hz electricity. Construct a problem in which you calculate the relative reduction in voltage of incoming high frequency noise compared to 60 Hz voltage. Among the things to consider are the acceptable series reactance of the inductor for 60 Hz power and the likely frequencies of noise coming through the power lines.
You are working in a factory and have been tasked with determining the electrical needs for a new motor that will be installed on an assembly line. The motor has been tested under load conditions and found to have a resistance of 35. and an inductive reactance of 50.0 . We can model the motor as a series RL circuit. The motor will have its own dedicated circuit with an rms voltage of 480 V. You need to determine the peak current drawn by the motor to determine the size of the circuit breaker needed to protect the circuit.
The power rating of a resistor used in ac circuits refers to the maximum average power dissipated in the resistor. How does this compare with the maximum instantaneous power dissipated in the resistor?
The current in the RL circuit shown below reaches half maximum value in l.75 ms after the switch S1is town. Determine (a) the tine constant of circuit and (b) the resistance of the circuit if L = 250 mH.
Review. A novel method of storing energy has been proposed. A huge underground superconducting coil, 1.00 kin in diameter, would be fabricated. It would carry a maximum current of 50.0 kA through each winding of a 150-turn Nb3Sn solenoid. (a) If the inductance of this huge coil were 50.0 H. what would be the total energy stored? (b) What would be the compressive force per unit length acting between two adjacent windings 0.250 in apart?
Some surgery is performed with high-voltage electricity passing from a metal scalpel through the tissue being cut. Considering the nature of electric fields at the surface of conductors, why would you expect most of the current to flow from the sharp edge of the scalpel? Do you think high- or low-frequency AC is used?