10)Examine each of the errors below, discuss how the error would affect the separation. Describe how each error would impact the efficacy of the purification (better separation, worse separation, no effect). (Error) a) Overbunched cotton ball at bottom of column b) The silica gel is not level when the sample is loaded onto the column c) Half as much silica gel was used as was indicated in the procedure d) Smaller fractions are collected (less volume in each test tube with test tubes switched more frequently)

10)Examine each of the errors below, discuss how the error would affect the separation. Describe how each error would impact the efficacy of the purification (better separation, worse separation, no effect). (Error) a) Overbunched cotton ball at bottom of column b) The silica gel is not level when the sample is loaded onto the column c) Half as much silica gel was used as was indicated in the procedure d) Smaller fractions are collected (less volume in each test tube with test tubes switched more frequently)

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

DATA REPORT FORM Procedure A: Ink Analysis by Paper Chromatography 1. Attach the chromatography paper results here. Name 2. Calculate the Rf value for each ink/marker sample. If there are more than one spot in the sample, calculate and list Rf for all components. Procedure B: Identification of Unknown Analgesic Drugs 1. Sketch the best results of the TLC plate here, including unknown sample and known compounds. 11
You are planning on performing column chromatography. You ran a TLC plate (below) on your crude mixture to test out the solvent system and stationary phase you plan to use for your column. What order would you expect the components to come off the column? Options: Red (C) first, then black (B) . Blue (A) won't come off the column Not enough information to determine Red first (C) , then black (B) , then blue (A) Blue (A) first, then black (B) . Red (C) won't come off the column Blue (A) first, then black (B) , then red (C)
Chemistry Question 10 4 According to the troubleshooting section for column chromatography in the laboratory textbook, select all that applies to why separation would not occur. Incorrect selections deduct points! The adsorbent surface at the top of the column is not flat and horizontal. Sample may have been overloaded onto a small column. Polarity of starting solvent for elution is too polar. Too much solvent was used for elution
QUESTION 15 To improve the accuracy of our linear fit between absorbance and concentration, a. add an extra data point to your linear regression where you make the assumption that pure water has an absorbance of zero. b. make sure that you choose a "Linear Regression" curve fit. c. ensure that there are no air bubbles in the cuvette. O d. use the data points only at the lower end of the concentration range because Beer's Law is not applicable for higher concentrations. QUESTION 16 What laboratory equipment do you need to prepare a 0.250 M stock solution of NaCI? O a. buret, graduated cylinder, analytical balance b. beaker, volumetric flask O. volumetric pipet, analytical balance d. analytical balance, volumetric flask
Please Explain clearly Why couldn’t you use acid-base extraction to separate a ketone and an alcohol? why do we use column chromatography instead? Please explain clearly the benefits of both methods and why is one method preferred over the other.
The following conditions may not cause tailing EXCEPT a. Thick filter paper as the stationary phase b. Uncovered chamber c. Volatile solvent d. Heavy sample spotting
How can the mass transfer "C" term be reduced? a. increase the flow rate b. reduce the size of the analyte c. increase the size of the analyte d. change the polarity of the solvent e. increase the length of the column f. reduce the flow rate
None
5. Summarize your conclusions from the TLC simulator. Circle the correct answer in each description about TLC separation of organic compounds on silica gel plates. a) A more polar compound has a lower/higher retention factor. b) A less polar compound has a lower/higher retention factor. c) A more polar solvent causes a lower/higher retention factor. d) A less polar solvent causes a lower/higher retention factor. e) To increase the retention factor of a spot, you should add more ethyl acetate/hexane.
what is the effect on the chromatographic peak if a. inserting/adding sample too slow b. column temperature is too high
Which solvent is appropriate to use in the iodoform test? Select one: Dioxane Acetone Please answer very soon will give rating surely Complete explaination needed Only correct answer needed
See image below