C. Experimental Procedure: (record Observations in notebook in ink) First Week Add 10 mL of glacial acetic acid to 5 mL of isoamyl alcohol in a 125 mL Erlenmeyer flask. (Because of the very unpleasant odor of acetic acid, dispensing of the acid and mixing with alcohol must be performed under the hood). Carefully add 3 mL of concentrated sulfuric acid (being careful not to wet the neck of the flask which will be in contact with the cork stopper), swirl the mixture, stopper tightly with a cork and store at room temperature until the next lab period. NOTE: Extreme care must be exercised in order to avoid contact with concentrated sulfuric acid. It will cause serious burns if it is spilled on the skin. If it comes in contact with the skin or clothes, it must be washed off immediately. In addition, sodium bicarbonate may be used to neutralize the acid. Clean up all spills, immediately!

C. Experimental Procedure: (record Observations in notebook in ink) First Week Add 10 mL of glacial acetic acid to 5 mL of isoamyl alcohol in a 125 mL Erlenmeyer flask. (Because of the very unpleasant odor of acetic acid, dispensing of the acid and mixing with alcohol must be performed under the hood). Carefully add 3 mL of concentrated sulfuric acid (being careful not to wet the neck of the flask which will be in contact with the cork stopper), swirl the mixture, stopper tightly with a cork and store at room temperature until the next lab period. NOTE: Extreme care must be exercised in order to avoid contact with concentrated sulfuric acid. It will cause serious burns if it is spilled on the skin. If it comes in contact with the skin or clothes, it must be washed off immediately. In addition, sodium bicarbonate may be used to neutralize the acid. Clean up all spills, immediately!

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

In the table below, record the color that you observe for each spot or component of each spot after the run is completed. For the retention factor, R₁, write in the numerator (top) the number of mm that the spot has moved and in the denominator (bottom) the number of mm that the solvent has moved from the point where the samples were 'spotted. Calculate the Rf vale for each spot or component of each spot. Im having a difficult time finding the Retention Factor for M&Ms by using Salt water and seeing how much each color moves Instructions Coffee filters usually are round, but it's easier to compare your results if the paper is rectangular. So, your first task is to cut the coffee filter into a rectangle. Measure and cut a 2-3/4" by 7" strip from the middle of a coffee filter. This is easily done by folding the filter in half (to make a half-circle) and then folding the half-circle into thirds. Cut along the 13-fold lines and trim the ends to make a rectangle. 2. Using a pencil (ink from…
Calculate the Rf value for a spot in a TLC experiment if the solvent moved 13.5 cm and the spot moved 9.1 cm from the origin. Type answer:
What is the purpose of thin layer chromography lab? What is a hypothesis I can use when conducting a TLC lab and how can that hypothesis be tested?
how does TLC determine if a sample is pure?
5. Summarize your conclusions from the TLC simulator. Circle the correct answer in each description about TLC separation of organic compounds on silica gel plates. a) A more polar compound has a lower/higher retention factor. b) A less polar compound has a lower/higher retention factor. c) A more polar solvent causes a lower/higher retention factor. d) A less polar solvent causes a lower/higher retention factor. e) To increase the retention factor of a spot, you should add more ethyl acetate/hexane.
Should you increase the diameter or length of the chromatography colum for increasing throughput?
thin layer chromatography: What would happen to the Rf value of a compound if you increased the polarity of the mobile phase while using a polar stationary phase? please help me this question! Thank you a lot
what is the effect on the chromatographic peak if a. inserting/adding sample too slow b. column temperature is too high