10–43. The shaft is made of A992 steel. It has a diameter of 25 mm and is supported by bearings at A and D, which allow free rotation. Determine the angle of twist of B with respect to D. B 90 N-m 0.6 m 90 N-m 0.75 m D 0.9 m

Q: Problem 1 An L-shaped bar is supported by a normal bearing at A and a smooth horizontal surface at…

A: Given data:- Below L-shaped bar diagram is given in question;

Q: The right-angle uniform slender bar AOB has mass m. If friction at the pivot O is neglected,…

A:

Q: A 200-lb force (P) directed vertically downward is applied to the toggle vise at C. Knowing that…

A: Given Data : Length of AB= 4 in Length of BC= 6 in length of BD= 6 in Force (P)= 200 lb

Q: PROBLEM 3 The bracket which is fastened to a wall by anchor bolts at A and B is loaded by the forces…

A:

Q: (ii) A 1.6 m long tubular shaft of 42-mm outer diameter d₁, having the cross-section shown is to be…

A:

Q: Replace the force system by an equivalent resultant force and couple moment at point O. Take F3 =…

A: Write all forces in vector form:

Q: Both shafts have the same diameter 2cm and are made of low quality steel G=77 GPa. A torque of 1200…

A: Given: Diameter of both the shafts: d=2cm=0.02m Length of the shaft AB: LAB=0.35m Length of the…

Q: P1 = 445 N P2 = 501 N Determine the force in member DC, use a positive value for tension or a…

A: A two-force member is defined as an element with pins or hinges at each end and no load in the…

Q: The members of a truss are connected to the gussetplate. If the forces are concurrent at point O,…

A: We can find the force using the component.

Q: 200 400 A В 200 N m E D 200 F Dimensions in mm Determine the magnitude of the force (in N) of the…

A: To find x component of internal pin at D

Q: The shaft is supported by a journal bearing at A and a thrust bearing at B. Determine the normal…

A: Consider the beam,

Q: Container W weighs 376 N. It is suspended from ring A. Cable BAC oases through the ring and is…

A: W=376 NTo find- Force vector for P and Q

Q: The solid 37 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the…

A:

Q: Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of…

A: Young's modulus of A-36 steel = 29007.5 ksiA point load of 10 Kip is applied at E.To determine the…

Q: The electric power transmission tower supports two wires that apply 18 kN vertical forces, and the…

A: Member DE is zero force member.

Q: 5-78. The bent rod is supported at A, B, and C by smooth journal bearings. Compute the x, y, z…

A: Introduction- A reaction force opposes an action force by acting in the opposite direction. During…

Q: QUESTION 2 Determine the bending moments for the frame below. 2kN EI B A 4KN 5m 2E1 10m с ΕΙ O 10m

A:

Q: The solid 28 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the…

A: Solution: Given: d = 28 mm E = 200 GPa P = 550 N Q = 1150 N LAB = 350 mm LBC = 600 mm LCD = 600 mm

Q: 1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is…

A:

Q: Ʈallow (MPa)=95     Ø(rad)=0.015     a (mm)=80    d (mm)=40

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.