PROBLEM 3 The bracket which is fastened to a wall by anchor bolts at A and B is loaded by the forces P=120N and the conterclockwise couple C= 140N-m. Replace P and C with a) an equivalent force couple system, the force of which acts at A. b) two vetical forces one acting at A and the other at B. 200mm Fam + 700 mm. 150 B A. + 1200mm 1 P=120N Dc

PROBLEM 3 The bracket which is fastened to a wall by anchor bolts at A and B is loaded by the forces P=120N and the conterclockwise couple C= 140N-m. Replace P and C with a) an equivalent force couple system, the force of which acts at A. b) two vetical forces one acting at A and the other at B. 200mm Fam + 700 mm. 150 B A. + 1200mm 1 P=120N Dc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 72 2 (a) 8 W+ W 2 (c) 2 2W+ с W) 2 T 72 30⁰ A beam AB of length 1 and weight w supports a load W at its free end B and is hinged at its end A. A wire CD supports the beam at the mid point C making an angle of 30° with the horizontal. What is the value of tension T in the wire CD? D B W (b) 4 (2W + w) (d) 4 W+ W 2
A solid 1.00-in.-diameter steel [G = 12000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. O-0.0653 rad O-0.0513 rad O-0.0415 rad O-0.0542 rad O-0.0316 rad B (2) 36 in. 215 lb-ft (3) 36 in. 110 lb-ft D
0. Determine the maximum force P that the top chord can carry if the allow shearing stress is 50MPa, bearing stress is 60MPa and tensile stress is 85MPa of the connection shown -3. 0 d a اما ماماه b C d 200mm 120mm 40mm 75mm 30°
The bracket BCD is hinged at € and attached to a control cable | ! at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a=0. 18m 20N 20N 8 c o I_.l_nm—l—um—-l 02¢m
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the tension at wire BD. E 4 m 3 m 2 m 2 m O 1.95kN O 1.64kN O 0.91kN O 1.29KN o o oO
4-91. If the couple moment acting on the pipe has a magnitude of 300 Nm, determine the magnitude F of the forces applied to the wrenches. -F A -150 mm -150 mm. B F 200 mm Probs. 4-90/91 600 mm A CO
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
The top of the folding workbench has a mass of 40 kg with mass center at G. Calculate the magnitude of the force supported by the pin at E. - 670 mm- G. D. 230 mm H. 975 mm E 1070 mm Answers: E = i N