A solid 1.28-in.-diameter steel [G= 13000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. B 36 in. 215 lb-ft (3) 36 in. 110 lb-ft

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: Draw the shear force and bending moment diagrams and sketch the qualitative deflected shape.

A: The figure given in the question are as follows: w=1.5 klf

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: What is ponit of view? What is first point of view and third point of view.

A: The term  Point of view will be referred to who is telling or narrating the story. A story can be…

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: Assignm R= Station 18+26 18+00 17+00 16+00 15+68 3: For Arc 0 Deflection Angle (DMS) 0°0'0" Chord…

A: Horizontal Curve :  In order to transition between two tangent strips of road, a horizontal curve is…

Q: BEGO AV 6 MM CM X 2 2 5 24 INCH Styles Title 1 No Spac..... Question 2: Given that this soccer field…

A: Given Goal to goal distance = 100 m Required  Representative factor,RF of image

Q: A line has a bearing of S 33 deg. 24° 54" E. What is its azimuth? Show diagram

A: The Azimuth of line A can be calculated by subtracting the given bearing to 180°. Calculation:…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: 14000 mm 3000 mm 8000 mm 3000 mrm 12000 mm ww 0009

A: Given:- The radius of the semicircle = 3000 mm The thickness of the wall = 500 mm  To determine:- a)…

Q: What are the commonly available switch actions?

A: Commonly available switch actions? ON-OFF, SPST. SPST = Single Pole, Single Throw.  (ON)-OFF,…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: -30- 15 Compute I, and I, for the plane region. 12.5 45 10 40 Dimensions in mm

A: Moment of inertia about X-axis:            Ix = 12.5x7033+27.5x1033+17.5x15312+17.5x15x70-7.52 Or,…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.