(ii) A 1.6 m long tubular shaft of 42-mm outer diameter d₁, having the cross-section shown is to be made of steel for which Towable = 75 MPa and G = 77GPa. Knowing that the angle of twist of the shaft must not exceed 4° when the 3 shaft is subjected to a torque of 900 Nm, determine the largest inner diameter d., which can be specified in the design. OFF d₁= 42 mm

(ii) A 1.6 m long tubular shaft of 42-mm outer diameter d₁, having the cross-section shown is to be made of steel for which Towable = 75 MPa and G = 77GPa. Knowing that the angle of twist of the shaft must not exceed 4° when the 3 shaft is subjected to a torque of 900 Nm, determine the largest inner diameter d., which can be specified in the design. OFF d₁= 42 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bronze C86100 pipe has an outer diameter of 1.5 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. If the torque developed at A is 125 lb # in., determine the magnitude F of the coupleforces. The pipe is fixed supported at end B.
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
a) Find minimum diameter needed if the allowable shear stress is I40 Mpa and the rotation of point A can't exceed 2.5 degrees. →Shaft made of steel 10 kN-m 4KN m 2KN -m 450 g00 mm 1goo mm A mm
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rigid bar G. If P = 5 kN, determine the horizontal displacement of end F of rod EF. -300 mm B DG E -450 mm 4P
Three cylindrical rods are welded together as shown in the f igure. The diameter and modulus of elasticity of the materials are given. If Q= 30kN; Evaluate the necessary P force make the def lection on B zero? b. Based on the calculate P force in (a) calculate the def lection on C? а. 300uL 125u 125. 300um d = 12mm E - 20Gpa d%3 8mm E = 20Gpa E= 20Gpa Q -P C A В
4-7. The assembly consists of two 12-mm-diameter A992 steel rods AB and CD, a 20-mm-diameter 6061-T6 aluminum rod EF, and a rigid bar AEC. If P = 20 kN, determine the displacement of F. P F 600 mm- 2P 2P E C Prob. 4-7 400 mm- B D
The figure below shows a shaft of three segments. It is restrained (fixed support) at both sices and is loaded by two torques. Use Groze -35 GPa, Glum - 28 GPa, and Getee - 83 GPa Aluminum Steel Bronze digmeter = 50 mm diameter = 25 mm diameter = 25 mm T-300 N.m K To =700 N.m4K 2 m 2 m 2.5 m Determine the maximum shearıng stress developed in aluminum. Select the corect response 214.16 MPa 175 MPa 57.12 MPa 111.79 MPa
A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in diameter, and four 10 mm. steel bolts on a bolt concentric bolt circle of 200 mm. in diameter. (a) Determine the torque applied (N-m) if the shearing stress is 60MPa in the bolts. (b) If the torque capacity increased to 8 kN-m, determine the number of bolts of 10 mm. diameter on the 300 mm. bolt circle of the coupling.
Q1/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple forces F causes the ends of the wrench to be displaced 3 mm, determine the maximum shear stress in the bolt. Assume that the wrench is rigid and modulus of rigidity of steel is 75 GPa. 150 mm i50 mm mni
A compound steel [G-82 GPa) shaft consists of solid 34-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 56 mm and an inside diameter of 51 mm. Determine: (a) the maximum shear stress 7₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle PD/A of gear D relative to gear A. L03 230 Answers: (a) T₂- (b) 0₂- (c) D/A- 1.8 B 230% MPa.
Determine the force of member BD. Include a negative sign if the answer is in compression. Indicate whether it is in tension (T) or in compression (C) in your solution. T-m- 40 kN Dt 60 kN 40 kN 3 m 7m A Az 3 m Ax Cy Plan AAA, 4 m
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson