10. Consider the following potential sources of experimental error. Predict whether these errors would produce a percent mass water that is higher (H), lower (L) or the same (S) as the theoretical percent mass water. Explain your answer. (Hint: it may be useful to consider how each of these errors would affect the apparent mass of the anhydrous salt, and how that would affect the apparent mass of the water lost.) a. When massing the anhydrous salt, some water was observed to remain around the mouth of the test tube. b. The anhydrous residue decomposed upon heating, liberating a gas other than water vapor. c. The hydrate spattered during heating and some of the hydrate sample was lost.

10. Consider the following potential sources of experimental error. Predict whether these errors would produce a percent mass water that is higher (H), lower (L) or the same (S) as the theoretical percent mass water. Explain your answer. (Hint: it may be useful to consider how each of these errors would affect the apparent mass of the anhydrous salt, and how that would affect the apparent mass of the water lost.) a. When massing the anhydrous salt, some water was observed to remain around the mouth of the test tube. b. The anhydrous residue decomposed upon heating, liberating a gas other than water vapor. c. The hydrate spattered during heating and some of the hydrate sample was lost.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Use the sample experimental data to calculate the mass of residue (BaCl2) Mass of pan 15.110 g 2. Mass of pan + sample before heating 17.452 g 3. Mass of pan + sample after heating 17.107 g
You were tasked to separate the components of a mixture containing silica, sodium chloride and charcoal. TNāCI dissolves in water while silica and charcoal are not water-soluble. Only charcoal dissolves in carbon disulfide. a. Write a short experimental procedure to carry out the separation of the mixture. b. Given the following data, determine the percentage of charcoal, sodium chloride and silica. Mass (g) Mass of beaker 100.000 Mass of beaker + mixture 110.000 mass of evaporating dish 62.000 mass of evaporating dish + solid after evaporation of water 65.000 Mass of beaker + charcoal + silica after evaporation of excess water 117.000 mass of beaker + silica after decanting dissolved charcoal and drying 113.545
Include a CLAIM: answer the question. For example, this answer is not correct. Include EVIDENCE: Describe what you see in the calculation work that supports your claim. In the answer the wrong conversion factor was used. When calculate mass we..... Include REASONING: Explain WHY you selected that evidence to support your claim. You should have a paragraph.
1. Give reasons why the helium atom is smaller than the cesium atom. 2. A student got a problem wrong. They were asked, “How many grams of MgCl2 (molar mass = 95.21 g/mol) are needed to make 3.16 L of a 0.500 M MgCl2 solution?” The correct answer is 150. but the student got 1.58. What mistake did the student make? 3. To solve the following problem what is the reason you must subtract the vapor pressure of water, 24 torr, from the total pressure, 747 torr in order to solve the problem? “A 500.0-mL sample of H2 gas is collected over water at 298 K and 747 torr. What volume would the dry H2 gas occupy at STP? (Given: the vapor pressure of water at 298K is 24 torr).” By the way, the answer is .436 liters. NOTE: I am not asking you to solve this problem. I am asking the reason for subtracting the vapor pressure. If you simply solve the problem, you will get no points.
and (II) chloride. are formed when aluminum reacts with cobalt If no reaction occurs, type NR in both boxes. Please use symbols, not full names, in your answer. For subscripts, please use full-size numbers. For example, H₂O would be entered as H20. Please don't confuse the letter "o" with the number "zero". Please don't confuse the letter "i" with the letter "1". and The products are Enter the free metal first. Enter the ionic compound second. Please include (aq), (I), (s) or (g) in your answers.
Based on this. What was the percentage by mass of water in the sample?
I think I did the first one Ii think I did the first one correctly, but I am unsure. I just know that they asking for it like that and also the changes of the element.
Please answer question 19 part A and B
How much 20.0% NaOH should I put in a 30.0 ml tube if my dilution ratio is 1/10. What is the concentration of the tube. ml of 20.0% Just put the number of mL Do not enter anything but a number. Use correct sig figs. Remember ratios and conversion factors do not enter the significant figure calculation. What is the concentration in percent. Again, correct significant figures. NUMBERS only not the % sign
Based on their calculations, a student expected their synthesis to yield 5.3 mmol of triphenylcarbinol (MW = 260.33 g/mol). After their reaction is completed, they report an actual yield of 0.82 g. What was their percent yield? %3D a. 16% O b. 4.0% c. 59% O d. 0.59%
Based on this. What mass of water was driven off by heating? (Grams)
1. What is the mass (grams) of 2500. carbon atoms? 2. What is the mass (grams) of 6.52 x 1018 atoms of gold (Au)? Is this the correct answer including the correct labels?