Question 1.11 A beam has a rectangular cross section and is subjected to a shear force V along the negative y direction, as shown in Figure Q1.11. Points A and B are located at the centre and bottom surface of the cross section. What is the correct statement? t B Figure Ql.11 O a. The minimum shear stress induced by the shear force is located at Point B and its value is zero. O b. The minimum shear stress induced by the shear force is located at Point B and its value is non-zero. O c. The minimum shear stress induced by the shear force is located at Point A and its value is non-zero. O d. The minimum shear stress induced by the shear force is located at Point A and its value is zero.

Question 1.11 A beam has a rectangular cross section and is subjected to a shear force V along the negative y direction, as shown in Figure Q1.11. Points A and B are located at the centre and bottom surface of the cross section. What is the correct statement? t B Figure Ql.11 O a. The minimum shear stress induced by the shear force is located at Point B and its value is zero. O b. The minimum shear stress induced by the shear force is located at Point B and its value is non-zero. O c. The minimum shear stress induced by the shear force is located at Point A and its value is non-zero. O d. The minimum shear stress induced by the shear force is located at Point A and its value is zero.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
The rectangular plate is deformed into the shape shown by the dashed lines. Suppose that a = 260 mm and b = 450 mm (Figure 1) 2 mm a mm D B 6 mm 6 mm 2 mm -3 mm -x 1.) Determine the average normal strain along diagonal BD. 2.) Determine the average shear strain Yzy at corner B relative to the x, y axes..
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm y 10 mm At-40 mm-- 30 гу 30 mm 10 mm 10 mm
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.
Question 1. The plane NN' makes an angle 0=30° with respect to the cross section of theprismatic bar shown in Figure. The dimensions of the rectangular cross section of the bar are 3cmx6cm. Under the action of an axial tensile load P, the normal stress of NN' plane is ơn =60 MPa. a.Determine the value of axial load P b.Determine the shear stress t on the NN' plane c. Determine the maximum shear stress in the bar. P N N'
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain 6x = 0.005, DA has a normal strain e, = 0.004 at D, y = 0.01rad determine the shear strain at point E with respect to the x and y' axes. 600 mm 600 mm
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in figure. A B BO Calculate the shear stress on oblique plane at 0 = 45° A 0.625 MPa C 0.31 MPa F D 1.25 MPa
A beam carries concentrated loads at each ends, and a triangular load shown in figure. The beam is a built up shown below. Determine the maximum value of P if the allowable bending stress is1200 psi and the allowable shear stress 200 psi. W=3P P n 4 FT R1 12 FT R2 4 FT
Two vertical forces, each of magnitude P= 8 kN, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 10 mm 10 mm 50 mm- 50 mm 10 mm The maximum tensile stress is The maximum compressive stress is T B 150 mm MPa. 250 mm MPa. C 150 mm
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Q/Normal and shear stresses acting at the point is shown in Figure 1- Determine the principal stresses and the maximum shear stress acting at the point . Show these stresses in an appropriate sketch . 2- If the element is rotated 30 deg clockwise then determine the normal stresses and the shear stress acting at the point . Show these stresses in an appropriate sketch .