1.1 Draw a component block diagram for each of the following feedback control systems. (a) The manual steering system of an automobile (c) The water level controlled by a float and valve In each case, indicate the location of the elements listed below and give the units associated with each signal. ⚫ The process The process desired output signal ⚫ The sensor ⚫ The actuator The actuator output signal ⚫ The controller ⚫ The controller output signal The reference signal The error signal Notice that in a number of cases the same physical device may perform more than one of these functions.

1.1 Draw a component block diagram for each of the following feedback control systems. (a) The manual steering system of an automobile (c) The water level controlled by a float and valve In each case, indicate the location of the elements listed below and give the units associated with each signal. ⚫ The process The process desired output signal ⚫ The sensor ⚫ The actuator The actuator output signal ⚫ The controller ⚫ The controller output signal The reference signal The error signal Notice that in a number of cases the same physical device may perform more than one of these functions.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

1.a. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The CPU in the main controllerC. The driverD. The axis logic card1.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine andcosine waveforms is called a/anA. tachometer.B. encoder.C. resolver.D. alternator.
MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Solve the the problem. -With Step by step solution -Include block diagram (if necesarry)
25.a. The type of sensors that are used on most simple brushless motors to identify motor rotor position aretheA. field-effect sensors.B. optical-range sensors.C. hall-effect sensors.D. capacitive sensor. 25.b. An encoder is being used instead of a tachometer in a DC servo system. This system of speed control iscalledA. dual-purpose feedback.B. open-loop feedback.C. dual-connection feedback.D. bit counting.
please give me an accurate ans with 30 minutes tq
What causes ground loops in an instrumentation system? What are the effects of a ground loop?
Consider a standard feedback control system where each component is functioning properly. Briefly indicate whether you agree or disagree with the following statements:(a)For proportional-only control, the controller output is always proportional to the error signal.(b)A PID controller always eliminates offset after a sus-tained, unmeasured disturbance.
27. A closed-loop control system requires the sensing unit (i.e. sensor) to send the system. (a) no feedback (b) a positive feedback (c) a negative feedback to
Q2) For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 Q). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a=60 ). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).
Is it option B? 1. In an open loop control system the control action is dependent upon;a) the size of the system b) system variablesc) the input signals d) the output signal
1. Explain briefly the working principle of an electro magnetic relay2. Draw the symbol for an electro magnetic relay 2NO and 1 NC3. Explain the working principle of a limit switch4. Explain the working principle of a reed switch5. What are the functions of sensors6. Enumerate what are the different input elements.7. What are the signal processing elements?
Name three applications for control systems and explain briefly why is it a control system Give one reason for not using feedback control system