HI need help asap! Thank you. 1. Pis a cube with 300mm sides and weighs 45kg per cubic meter. Rope CB is 20mm indiameter and can carry 1000kPa.A. At what distance x is the critical point for the rope CB?At x=500m,B. Draw the shear and moment diagrams of beam AB using any method.C. What is the maximum shear at AB if it is a hollow pipe with inside diameter of10mm and 2mm thickness?D. What is the maximum axial force at AB?E. What is the axial stress at the rope CB?PROBLEM 2:Given:P = 5kNQ = 12kNL=1200mmThe member is a solid material of 30mmx30mm cross-section.Find/answer the following:If theta is 45degrees,A. Axial stress (MPa) at the support.B. Axial stress (MPa) at L/2.C. Shear stress (MPa) at the support.D. Shear stress (MPa) at L/2.E. Shear diagram using any method. (5pts) F. Moment diagram using any method.If theta is unknown,G. At what theta will the compression capacity of the member fail if the allowable compressivestress is 9MPA? Problem 1Problem 21.5mP-2.4m

Answered: Image /qna-images/answer/d54a883e-5eec-4c59-a6b8-4a3f428833ee.jpg

1. Pis a cube with 300mm sides and weighs 45kg per cubic meter. Rope CB is 20mm in diameter and can carry 1000kPa. A. At what distance x is the critical point for the rope CB? At x=500m, B. Draw the shear and moment diagrams of beam AB using any method. C. What is the maximum shear at AB if it is a hollow pipe with inside diameter of 10mm and 2mm thickness? D. What is the maximum axial force at AB? E. What is the axial stress at the rope CB?

1. Pis a cube with 300mm sides and weighs 45kg per cubic meter. Rope CB is 20mm in diameter and can carry 1000kPa. A. At what distance x is the critical point for the rope CB? At x=500m, B. Draw the shear and moment diagrams of beam AB using any method. C. What is the maximum shear at AB if it is a hollow pipe with inside diameter of 10mm and 2mm thickness? D. What is the maximum axial force at AB? E. What is the axial stress at the rope CB?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Related questions

Q: Where does your drinking water come from? Describe the source of your water at eitherhome or school,…

A: The following diagram shows the water supply system from source to distribution.

Q: You will present a 4 minute informative speech to the class. Informative speech topic should be…

A: Given data,this is the opinion type of question. Answer may vary person to person as per his…

Q: Explain what a building sprinkler system is and give examples of various types of sprinkler designs

A: Fire Extinguishing Systems and Prevention in Buildings are other important aspects that can provide…

Q: Question 50 An activity is the lowest level in a WBS and has a work package below it. True O False

A: True. Work package would be below the activity. Work package is the most lowest segment of working…

Q: Please make a PERT CPM use the activity and duration below. Also use the format stated. PLEASE DON'T…

A: I will create a PERT CPM (Program Evaluation Review Technique Critical Path Method) chart using the…

Q: potential challenges with regards to emergency preparedness, space management and sustainability in…

A: Emergency planning has a number of obstructions happening where there is always confusion among…

Q: How is the CPM scheduling program helpful to the Engineers?

A: The Critical Path Method (CPM) scheduling program is an activity-oriented network program used for…

Q: Investigate and report the main safety issues emphasized ina country of your choice other than the…

A: Chosen country : India Construction, which was basic to developmental activities provides various…

Q: What does the term sex offender describe? A person who is required to register with the school board…

A: What does the term sex offender describe? A person who is required to register with the school board…

Q: Using the Table of Contents for the regulations, in which section would you find regulations…

A: OSHA gives all the safety regulations regarding staircases and ladders . Section 15 tells about the…

Q: A building has an area of 16656 ft2. What is the minimum number of roof drains required?

A: The area of the building = 16656 ft2 We need to calculate the minimum number of drains required.

Q: Describe,how a boiler feed water treatment system work?

A: The boiler feed water is treated with proper techniques to remove all the minerals , suspended…

Q: Identify every activity that is considered civil work scope a)Rebar b)Grout c)Dewatering…

A: Fireproofing, however, is typically not considered part of civil work but rather a part of building…

Q: Who is responsible for developing an inspection plan?

A: Inspection of any sort of work is an important parameter for ensuring its safety, performance and…

Question

HI need help asap! Thank you.

1. Pis a cube with 300mm sides and weighs 45kg per cubic meter. Rope CB is 20mm in
diameter and can carry 1000kPa.
A. At what distance x is the critical point for the rope CB?
At x=500m,
B. Draw the shear and moment diagrams of beam AB using any method.
C. What is the maximum shear at AB if it is a hollow pipe with inside diameter of
10mm and 2mm thickness?
D. What is the maximum axial force at AB?
E. What is the axial stress at the rope CB?
PROBLEM 2:
Given:
P = 5kN
Q = 12kN
L=1200mm
The member is a solid material of 30mmx30mm cross-section.
Find/answer the following:
If theta is 45degrees,
A. Axial stress (MPa) at the support.
B. Axial stress (MPa) at L/2.
C. Shear stress (MPa) at the support.
D. Shear stress (MPa) at L/2.
E. Shear diagram using any method. (5pts) F. Moment diagram using any method.
If theta is unknown,
G. At what theta will the compression capacity of the member fail if the allowable compressive
stress is 9MPA?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
For the beam shown: (a) determine the distance a for which the maximum positive and negative bending moments in the beam are equal; and (b) draw the corresponding shear and bending moment diagrams for the beam.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in Figure P8.6. Find the vertical stress increase at A.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The cross section of a braced cut supporting a sheet pile installation in a clay soil is shown in Figure 14.22. Given: H = 12 m, clay = 17.9 kN/m3, = 0, c = 75 kN/m2, and the center-to-center spacing of struts in plan view, s = 3 m. a. Using Pecks empirical pressure diagrams, draw the earth-pressure envelope. b. Determine the strut loads at levels A, B, and C.
A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = . Use Eq. (7.4).