1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If the allowable stresses are 140 MPa for bearing in the plate material and 80 MPa for shearing of the rivet, determine the minimum thickness of each plate. b. Under the conditions specified in part (a), what is the largest average tensile stress in the plates? Figure:

1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If the allowable stresses are 140 MPa for bearing in the plate material and 80 MPa for shearing of the rivet, determine the minimum thickness of each plate. b. Under the conditions specified in part (a), what is the largest average tensile stress in the plates? Figure:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: O MPa and an axial stress of 325 MPa that act on an element imposes a bending stress of 250 MPa and…

A: Tangential stress is .Axial stress is .Bending stress is .Torsional stress is .

Q: A compound bar is constructed from three bars 50 mm wide and 12 mm thick fastened together to form a…

A: This question is of Solid of mechanics, Here the bar is compound.

Q: H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports…

Q: HW2: A steel shaft and an aluminum tube are connected to a fixed support and to a rigid disk as…

Q: Q3 - A thin-walled cylindrical vessel has an internal diameter of 1m and a thickness of 10 mm…

A: pressure:- Pressure is defined as the physical force exerted on an object. The force applied is…

Q: A solid bar has a diameter of 40 mm and subjected to the loadings shown in Figure 2. The supports at…

Q: Determine the maximum axial force P that can be applied to the bar in the figure below. The bar is…

Q: As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial…

Q: circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force…

Q: Determine the maximum shear stress in the shaft (Figure 1). Given the torsional shear stress is 45…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is…

Q: Determine the state of stress at point A on the cross section of the beam at section a-a. Take P =…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: A motorcycle's clutch hand lever is designed to receive a load from the rider's finger of 50 N at…

A: &#x3C3;=F&#x200B;A" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: Şekilde gösterildiği gibi sıcaklık 24°C ikem 0,5 mm'lik boşluk bırakılmıştır. Alüminyum çubuktaki…

Q: The cylinder in the figure below consists of spirally wrapped steel plates that are welded at the…

A: Given:The thickness of the wall is .The axial load is .The outside diameter of the cylinder is…

Q: he bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear…

A: Let us draw the Free body diagram

Q: A 1-m long copper bar is placed between two rigid, unyielding walls, as shown, with only one end…

A: The stress developed in the bar.Given:The length of the bar is .The temperature rise is .Obtain…

Q: The rectangular bar is connected to the support bracket with a 15-mm-diameter pin. The bar width is…

Question

1. In the figure, assume that a 20-mm diameter rivet joins the plates which are
100 mm wide.
a. If the allowable stresses are 140 MPa for bearing in the plate material and 80
MPa for shearing of the rivet, determine the minimum thickness of each plate.
b. Under the conditions specified in part (a), what is the largest average tensile
stress in the plates?
Figure:
P.
PD
-t = ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 From shearing of rivet:

VIEW

Step 2 Largest average tensile stress in the plate:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

t=10 mm b=240 mm F.S=1.9 σall=230 MPa
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 175 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 8 mm, and an allowable normal stress of 175 MPa. Assume x1 = 2.9 m, x2 = 1.4 m, and y1 = 3.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) C Answer: Pmax i kN
P (1) B A A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the following: The area of Segment (1) is equal to in mm?: The area of Segment (2) is equal to in mm²: The axial force (P) is equal to in kPa: The Normal Stress in Segment (2) is equal to in MPa:
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
Question 1 Two circular rods of 50 mm diameter are connected by a knuckle joint, as shown in Figure 1, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin. 50 x 11.00 in Rod (1) Pin Rod (2)
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
Please full solution with the drawing. Big and clear handwriting