t=10 mm b=240 mm F.S=1.9 σall=230 MPa 1. The vertical force P acts on the bottom of the rod having a negligible weight and arectangular cross section. The rod has a thickness of t(mm) and Pacts along the centerline of this thickness.a) Determine the shortest distance d to the edge of the rod at which it can be(eccentrically) applied so that it produces no compressive stresses on the rod atsection a-a (Case in Figure A).b) What would be the maximum value of P for the given allowable stress Oall andFactor of safety F.S if P was applied at the middle of the rod (Figure B)?300 mm300 mmaab mm500 mmb mm-500 mmda - aPPFigure BFigure A

Answered: Image /qna-images/answer/9289524e-f0e7-4eec-afe6-61c770d56922.jpg

Answered: The vertical force P acts on the bottom…

The vertical force P acts on the bottom of the rod having a negligible weight and a rectangular cross section. The rod has a thickness of t(mm) and P acts along the center line of this thickness.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the total elongation of the figure shown. Use E1 = 70 GPa, and E2 = 100 GPa 0.5 m 1.0 m F = 175 kN D2₂ = 0.06 m D₁ = 0.12 m side view 0.075 mm 0.73 mm 1.2 mm O 3.0 mm O None of the above end view
Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ P L2 Aluminum B Copper CP A Answer: P= i kips
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Aluminum A=600 mm2 Bronze Steel A=400 mm2 A= 300 mm2 2P 3P 4P P -3 m - - 5 m - - 4 m -
Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and 3. compressive stresses in portion BC of the beam. [ans: -79.8 MPa, 118.2 MPa] 200 mm 25 mm 25 mm 150 mm 25 mm 100 mm 100 kN 100 kN 15 m 0.5 m 05 m
at question A=110 MPa B=-60 MPa M=145 N.m
Determine the values of the stress in the steel bar as shown in the figure below when the temperature of the bar is -50°F, knowing that a close fit exists at both of the rigid supports when the temperature is +75°F. Use the values E = 29 x10 psi and a=6.5 x106 /°F for steel. A = 0.6 in B A - 24 in.- A 67,860 lbs B) 14,137.5 lbs c) 28, 275 bs D) 2827.5 Ibs
The permissible shear stress for the weldment in Figure is 109.2 MPa. Estimate the second polar moment of area. Take F = 20.7 kN, a = 104 mm and h = 7 mm. Give your answer in mm². Work to 3 decimal places. Do not submit the answer with units. h a h 180 mm ןד 150 mm
The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L = 460 mm, H = 345 mm, d₁ = 3 mm, d₂ = 5 mm, d3 = 13 mm, d4 = 8 mm, d5 = 3 mm, and de = 6 mm. Figure H B A dz dg ds + 1 of 1 Part A Determine the shear strain Yzy at corner A. Express your answer to three significant figures and include appropriate units. ol Di μA ? (YA)zy = Value Units Submit Request Answer Part B Determine the shear strain Yzy at corner B. Express your answer to three significant figures and include appropriate units. Di μA ? (YB)Ty = Value Units Submit Provide Feedback Request Answer
Values are m= 360mm n= 375mm q= 24mm r= 18mm P= 0.6kN
sigma x =10 Mpa
at question A=110 MPa B=-60 MPa M=145N.m