1. Given is the cross-section of a stream with uniform flow having a slope of 0.007 and the roughness coefficient of the stream bed is 0.025. Determine: a. Hydraulic radius b. Average velocity of the stream using Manning's coefficient and the corresponding discharge c. Average velocity of the stream using Kutter's coefficient and the corresponding discharge. 5.5 m 6.0 m 6.0 m 6.0 m 5.5 m 2.7 2.4

1. Given is the cross-section of a stream with uniform flow having a slope of 0.007 and the roughness coefficient of the stream bed is 0.025. Determine: a. Hydraulic radius b. Average velocity of the stream using Manning's coefficient and the corresponding discharge c. Average velocity of the stream using Kutter's coefficient and the corresponding discharge. 5.5 m 6.0 m 6.0 m 6.0 m 5.5 m 2.7 2.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For Manning's Equation, the letter A/P represents the hydraulic radius. * O False O True The Kirpich…

A: For Manning's Equation, the letter A/P represents the hydraulic radius. --》TRUE Explanation: R=A/P…

Q: Q4. Water flows along the rectangular channel such that after it falls to the lower elevation, the…

Q: 5. When depth of flow is more than critical depth, it is called as: a) Supercritical flow b)…

A: 5. The water profile is classified based on the flow of water longitudinally. They are classified as…

Q: A channel having a cross-section shown below has a flow rate of 0.049 m^3/s. Compute the hydraulic…

A: Hello dear, The answer is found to be Hydraulic radius R=1.845 m For explanation please see the…

Q: ater flows through an open channel that has a cross-sec own in the figure. Flow is uniform and the…

Q: Example 2.2 A 3 m wide trapezoidal irrigation channel shown in Figure 4 with side slopes (1:2)…

Q: A trapezoidal channel with uniform flow depth 4 m. The base width is 6 m and the side slopes are…

A: For different surfaces Manning's roughness coefficient is given. It is required to find weighted…

Q: In 1957 H. Görtler proposed the adverse gradient test cases U =- U. (1 + x/L)" and computed…

A: Given Data: Stream velocity n=1 xsep/L=0.159 θ0=0

Q: Hydraulic Radius Determine the general expression for the hydraulic radius of a circular pipe…

A: The area of pipe is (A) = Pi x dia^2 x 0.25 Coming to wetted perimeter : Here, the pipe is full…

Q: Water flows under a sluice gate in a horizontal rectangular channel of 2 m wide. If he depths of…

Q: A) what is the number of drop of the flownet? B) What is the flow of water in the unit of cm^2/min?…

A: The given figure shows a concrete dam on-site and its corresponding flow net.The coefficient of…

Q: weir installed at the end of a rectangular channel controls the flow of water. The rate of flow is…

A: To find percentage error in discharge measured

Q: Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line…

A: The pressure head,

Q: A rectangular river channel 4.6 m wide carries water at a depth of 0.6 m. The slope of the channel…

Q: 10. The Hydraulic radius of an Equalength-triangular channel of length (L = 20 cm) and height (h =…

Q: 48. What is the hydraulic radius in meters? 0.631 0.575 0.592 0.381 49. What is the mean velocity of…

Q: Water flows downward in a pipe of 600 mm diameter at the rate of 2 m³/s. It then enters a conical…

A: Rate of flow Q=2m3/sdiameter of conical duct DA=600mm.Diameter of conical duct DB=300mm.Length of…

Q: Hardy-Cross method is used for the solution of the pipe network flow distribution using the eq as…

A: Given:- ∆Q= -0.1 m^3/s Pipe Q Qc=Q - ∆Q AB 0.7 0.7- (-0.1)=0.8 BC 0.4 0.4-(-0.1)=0.5…

Q: Un earth dam made from homogeneous soil coefficient of permeability k=5x10^-4 Level of top dam =…

A: soil is isotropic then the permeability in both the direction is same. the phreatic line is the top…

Q: For a flow in a rectangular channel of width 5 m and depth of flow of 2.3 m the Darcy Weisbach…

A: Given rectangular channel with,Width of the channel, B =5mDepth of the flow in the channel, y = 2.3…

Concept explainers

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.

Question

Given is the cross-section of a stream with uniform flow having a slope of 0.007 and the
roughness coefficient of the stream bed is 0.025. Determine:
1.
a. Hydraulic radius
b. Average velocity of the stream using Manning's coefficient and the
corresponding discharge
c. Average velocity of the stream using Kutter's coefficient and the corresponding
discharge.
5.5 m
6.0 m
6.0 m
6.0 m
5.5 m
2.0
2.7
2.4
1.2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction:

VIEW

Step 2 (a) : Hydraulic Radius:

VIEW

Step 3 : (b) Velocity and Discharge Using Manning's Equation:

VIEW

Step 4 (c) Velocity and Discharge Using Kuttler's Formula:

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 5 : Please answer parts 1 & 2
Water flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m, the Froude's Number is 3. If the water undergoes a hydraulic jump: Determine the Froude's number downstream of the jump. A 0.339 B 0.384 0.435 D 0.486
a water resource engineer is in charge of designing atrapezoidal open channel for flood control. Typically, these types of channels are made ofconcrete. Use Manning’s Equation.Flowrate (Qb), channel slope (S0), bottom width (Bw), channel sidewall angle (θ), actual depth(y), and Manning’s coefficient (n) are tabulated below. State all assumptions. * z is the sidewall ratio: for every 1 unit increase in depth, the top width increases by z on eachside of the channel, or 2z total.A) Given the actual depth, y = 1.25 ft, find the discharge Qa.B) Find the Critical Depth, yc, for the discharge Qa found in (a). For a trapezoid,dA/dy =Bw +2 yz .Is the flow sub- or super-critical?C) Determine the uniform flow normal depth (yn) at Qb = 209 cfs.D) If the slope is increased to 0.001, what roughness coefficient would be needed tomaintain the same discharge Qa? What about for Qb? Would it be the same value?
Q(4)A trapezoidal channel has side slopes of 3 horizontal to 4 vertical and the slope of its bed is 1 in 2000. Determine the optimum dimensions of the channel if it is to carry water at 0.5 m3/s. Take Chezy's constant as 80.