Answered: 1. Determine force in member BC, FG and…

1. Determine force in member BC, FG and CG. (BC= 35 kN (T), FG = 39.13 kN (C), CG= 17.5 kN (C)) 3 m Ec 2 m 40 KN B 20 kN G 2 m 2 m H 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The unsymmetrical built-up section of the given dimensions supports the given load shown. Determine the maximum fv or the beam shear developed in MPa. 10 KN 7 KN 6 KN/m 12 KN/m 1m 3m 2m a
Determine the maxi mum shear stress deue loped in the beam 5 KN/m Ø4 cm Ø3 cm 3 N/m 0.2 m 0-2m 0.2
A continuous beam is loaded as shown 1. Which of the following gives the fixed end moment AB in kN-m? a. 12 kN-m b. 8 kN-m c. 10 kN-m d. 5 kN-m 2. Which of the following gives the distribution factor at B for the member BA in %? a. 33.3% b. 66.6% c. 35.47% d. 45% 3. Which of the following nearly gives the moment at B using moment distribution method in kN.m? a. 12.89 b. 13.2 c. 11.2 d. 14.6
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Determine the load intensity, w at B and the distance “a” (b) what are thereactions at A and B ?
Problem 5: Replace the loading by an equivalent resultant force and couple moment at point O. 0.5 m 0.7 m F,=(-2 i+5j-3 k) kN 0.8 m F = (8 i– 2 k} kN
A propped beam of length 6m carries a concentrated load of 130kN, 2m from the fixed support and 40kN, 4m from the fixed support as shown: 2 130 2 40 2 a. Determine the plastic moment if the collapse mechanism occurs under the 130kN load. b. Determine the plastic moment if the collapse mechanism occurs under the 40kN load. c. Determine the plastic moment capacity.
The beam below is subjected to a uniformly distributed load of 2 kN/m from a A to C, and a uniformly varying load (2kN/m to 5 kN/m) is applied at C to F. Two uniformly distributed loads support the beam on the location shown below. U, 9-2 w, 1 (m) 1 ( 2 (m) 1 (m) D 5. Determine the magnitude of W; in kN/m. 6. Determine the magnitude of W, in kN/m. 7, Determine the maximum moment. B. Determine the location of zero shear.
3.11 (B). A beam, 12 m long, is to be simply supported at 2m from each end and to carry a u.d.i. of 30 kN/m together with a 30 kN point load at the right-hand end. For ease of transportation the beam is to be jointed in two places, one joint being situated 5 m from the left-hand end. What load (to the nearest kN) must be applied to the left- hand end to ensure that there is no B.M. at the joint (i.e. the joint is to be a point of contraflexure)? What will then be the bes position on the beam for the other joint? Determine the position and magnitude of the maximum B.M. [114 kN, 1.6 m from r.h. reaction; 4.7 m from 1h. reaction; 43.35 kN m.) present on the beam.
Two distributed loads act on the beam AB. If the resultant of this loads is a 960 KN-mcounterclockwise couple (a) Determine the load intensity, w at B and the distance “a” (b) what are thereactions at A and B
2.0 ft 2.0 ft Determine the magnitude of Pfor which slipping impends, provided h is within the range where it does not cause tipping. a 270 lb b 135 lb c 540 lb d 315 lb If the magnitude of Pis 250 Ib determine height h a 4.44 ft which tipping impends. b 2.40 ft W = 600 lb c 3.00 ft d 4.80 ft Hs = 0.45
Situation 2. Determine the member forces BD, CD, and CE using Method of Section. Indicate if (T) or (C). A 50 KN B 4 m 6m C 100 KN 3m E D 200 KN 3 m F