2. Determine the internal forces for all members of Truss Bridge as shown below using: a. Equilibrium of joint method b. Influence line method F G H 4.6 m E 4.6 m 4t 4t 4t Determine the internal forces for all members of Truss Bridge as shown below using: a. Equilibrium of joint method b. Influence line method

2. Determine the internal forces for all members of Truss Bridge as shown below using: a. Equilibrium of joint method b. Influence line method F G H 4.6 m E 4.6 m 4t 4t 4t Determine the internal forces for all members of Truss Bridge as shown below using: a. Equilibrium of joint method b. Influence line method

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is subjected to a Point Load of 1000 Newton. Joint A is subjected to a Point Load of 1500 Newton. Show the values of Fat the beginning of the solution as well as the calculation steps and answer in the unit Newton. Using the Method of Joint, determine the forces in each member of the trusses shown in the following figure. 1500N 1000 N 12m 12m В 8 m E 6 m 12m 6 m Analyze whether the member is in Tension or Compression.
Solve the following neatly, systematically and completely. Show or submit solution Determine the forces in members EF, BF and BC.
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P A 45° 45° B L (a)
Solution pls
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
The 10-element truss system structure is loaded as shown in the figure. Determine the zero bars and the load values for each element. Indicate whether the elements are under tension or pressure. (A and B are fixed support)
Determine the deflection 8g at the free end of a cantilever beam AB with a uniform load of intensity q=4 kN/m acting over the middle of the length and a point load. The lenghth of beam is equal to L=3 m. The beam has flexural rigidity El=4286311 Nm². Note that upward deflection is positive. P=qL/6 A +4 3 9 L 3 13 B ↑
Can you help me with these practice questions please.
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
Flexure stress *Please answer in complete solution and draw the shear and moment diagram, Solve the Area moment of inertia*
3. Using the given figure below, determine the reaction of strut member DE and determine the reaction of pin at joint C (use member ABCD). - 2.5 m - 2.5 m 3.5 m C D F 1 m E 3 m 50 A 100 kN