3. Using the given figure below, determine the reaction of strut member DE and determine thereaction of pin at joint C (use member ABCD).- 2.5 m- 2.5 m3.5 mCDF1 mE3 m50A100 kN

Answered: 3. Using the given figure below,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @5 Hz when constant 120 KW is applied. Use the following: G(alum)-28 GPa, a=1.80 m, b=0.80m & L-2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is_KN-m B E 1.18 0.48 2.64 3.82 5.03
Given: picture. Find: determine the reactions at the beam supports at A& D for the given loading.
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
A laminated plastic beam of square cross section is built up by gluing together three strips, each 10 mm x 30 mm in cross section (see figure). The beam has a total weight of 3 N and is simply supported with span length L = 300 mm. 10 mm 10 mm 30 mm 10 mm 30 mm Considering the weight of the beam (9) calculate the maximum permissible CCW moment M that may be placed at the right support. (a) If the allowable shear stress in the glued joints is 0.5 MPa. Round to the nearest tenth. Mmax =| N.m (b) If the allowable bending stress in the plastic is 8 MPa. Round to the nearest hundredth. Mmax =| N. m
The cantilever beam shown is an aluminum pipe that has an outside diameter of 114 mm and an inside diameter of 97.3 mm. A moment of 3 kN-m is applied at the free end. Find the rotation at the free end of the pipe. Neglect the weight of the pipe. М 33KN.m 2m Mod. of Mod. of Coeff, of Elasticity Rigidity G Thermal Ultimate Strength Density kg /m3 x 10 Tensile Yield Strength F, MPa Expansion a m/m/C x 10-6 Poisson's MPa MPa MPa Ratio Material x 10 x 10 Tens. Comp. Shear Steel ASTM A36 or A501 7.85 207 83 250 400 11.7 0.25 Steel (high-strength low-alloy) ASTM A992 7.85 207 83 345 450 11.7 0.25 Steel AISI 1020 hot-rolled 7.85 207 79.3 210 380 11.7 0.25 Steel AISI 1040 hot-rolled 7.85 207 79.3 290 520 11.7 0.25 Stainless steel 7.85 200 80 280 580 410 11.7 0.25 (annealed) Cast iron (gray) 7.21 103 41 140 550 220 10.6 0.26 Aluminum allov 2.64 70 28 240 260 190 23.6 0.33 6061-T6 Magnesium alloy 1.794 45 17 210 280 140 26.1 0.34 Titanium alloy 4.40 114 45 900 970 690 9.7 Nominal Outside Inside…

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

3. Using the given figure below, determine the reaction of strut member DE and determine th reaction of pin at joint C (use member ABCD). 2.5 m - 2.5 m- - 3.5 m B C D m F E 3 m 50 A 100 kN