effective depth of 550mm and the width of the web section is 300mm. It is reinforced at the bottom with a steel area of 2800mm2. fc’ = 21MPa, fy = 350MPa. if the dead load is 18kN/m including its own weight acting along its entire length of 5m, the concentrated live load that it can carry acting at L/2 from the support is

effective depth of 550mm and the width of the web section is 300mm. It is reinforced at the bottom with a steel area of 2800mm2. fc’ = 21MPa, fy = 350MPa. if the dead load is 18kN/m including its own weight acting along its entire length of 5m, the concentrated live load that it can carry acting at L/2 from the support is

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

1. Replace the existing beam with a wide flange structural steel. The maximum flexural stress of steel is limited to 120 MPа. 50 KN 250 mm T 50 mm 10 KN/m 20 KN/m 350 mm 200 mm 3 m 2 m В 4 m A
A rigid beam (ABCDE) with negligible mass is pinned at (C) and supported by two rods, Determine: a) The load in each rod. b) The vertical movement of point A. A B C E 1m 1 m 3 m 2 m Steel A=600 mm E-200 GPa L-3 m 20 KN 5 KN Aluminum A-900 mm E-70 GPa ア L-4 m ケ

2. Straight beam AE is pin-connected at its 200 lb 400 lb one end A and to an L-shaped beam EF at its other end. EF is pin-connected at point F. Assume both beams to be weightless. If beam AE is subjected to the loads, as shown, and if the system is in 10 in 10 in 10 in equilibrium in the position shown, a) draw the FBD 20 in of beam AE, and b) using the FBD, calculate the resultant reactions at points A and E. 15 in
From the given figure below, determine the maximum flexural stress of the beam if it has a cross section of 150mm wide by 250mm deep. (JN 10 N/m o' RA=42N 42N 3M B IM 75Nm 81NM Im RD=3N -3N 0° 78 Nm 3NM V-DIAG M-DIAG
Compute the maximum flexure stresses for the beam loaded shown 15 KN/m 2m 150 mm 250 mm w=6KN/m 3m 1m B
SITUATION 20: The T-beam in the floor system has a slab thickness of 100 mm and supported by beams 5.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 1.5 m on centers and width of the web is 300 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 6 -28mmo bars and in compression side with 4 -28mmo bars. d'=66 mm. fe' = 24 MPa. fy = 350 MPа. NSCP 2015 specification states that the width of slab effective as T-beam flange shall not exceed one -quarter of the span length of the beam and the effective overhanging flange width on each side of the web shall not exceed: a) Eight times the slab thickness, and b) One-half the clear distance to the next beam 59. Which of the following most nearly give the effective width of the flange? а. 1500 mm c. 1250 mm b. 1375 mm d. 1000 mm 60. Which of the following most nearly gives compression block? а. 73.49 mm c. 46.10 mm the depth of rectangular b. 62.47 mm d. 63.51 mm 61. Which of the…
514. The right-angled frame shown in Fig. P-514 carries a uniformly distributed loading equivalent to 200 N for each horizontal projected meter of the frame; that is, the total load is 1000 N. Compute the maximum flexural stress at section a-a if the cross section is 50 mm square. Ans. a = 30.0 MPa -3 m 4 m Figure P-514 and P-515 5 m 2 md 03 m
7. For the beam and loading shown, determine the reaction at the roller support. The beam is W200X71 with E=180GPa and L=8m with load density of 2kN/m A W -L- B
I need a quick solution with fbd.
calculate for the force at member FH calculate for the force at member GH calculate for the force at member GI
A bridge girder AB on a simple span of length L = 30 m supports a distributed load of maximum intensity q at mid-span and minimum intensity q/2 at supports A and B that indudes the weight of the girder (see figure). 450 mm 32 mm B 30 m 16 mm- 1800 mm 32 mm 450 mm The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q (in kN/m) based upon the following. (a) solely based on an allowable bending stress aallow = 110 MPa kN/m (b) solely based on an allowable shear stress tallow = 50 MPa kN/m (c) accounting for both an allowable bending stress ollow and an allowable shear stress Tallow kN/m
At-beam has a width of flange equal to 700mm and a thickness of 100mm. It has an effective depth of 450mm and the width of the web section is 350mm. It is reinforced at the bottom with a steel area of 2925 sq.mm. fc'=17.24MPa, fy=413.7MPa. The concentrated live load that it could support at its midspan if it has a dead load including its own weight of 20kN/m with the beam span of 6m is _kN.A. 132kNB. 152KNC. 112kND. 92kN