Problem 1: Solve for the resultant of the force system shown: F1 = 30lb F2 = 50lb e = 37° e = 45° 0 = 60° F3 80lb %3D X- Pro res

Q: Problem Statement The rigid structural member is subjected to of the two 100-N forces. Replace this…

A:

Q: A simply supported wide-flange beam has the cross-section and loading as shown in the figure below.…

A:

Q: a) The equivalent forces of x-component. b) The equivalent forces of y-component. c) The resultant…

A:

Q: Draw the Shear and Moment Diagrams ラド |5- W=3K/FT. D B う 201 in

A: for equilibrium sum of forces in y axis is equal to zero, RA+RC-5-15-3×20=0RA+RC=80 k For…

Q: structural beam and Figure 2 the cross section the beam. Additional to all  the loadings shown beam…

A: Given:-OD=120mmt=7mmE=200GPaG=70GPaTo find:-principle and in plane maximum shear strains

Q: A RIGID BAR "AB" ATTACHED TO TWO VERMCAL RODS IS HORIZONTAL BE FORE LOAD "P" IS APPLIED. DETERMINE…

A: Given Data  Length of steel = 2.4m = 2400 mm  Length of aluminum = 1.4m = 1400 mm Modulus of…

Q: Pls answer following question provide a hand written sol.

A: Step 1:Step 2:Step 3:

Q: QUESTION 2 PROBLEM 2: Calculate the components of the forces at B and C. A D E F b Given: P= 21 kN a…

A:

Q: A truss frame is shown below, using Virtual Work Method determine; Use: E = 200 000 MPa, A = 150 mm?…

A:

Q: 100 kN -1.2 m 9'0

A: To find the vertical and horizontal displacement of joint D -

Q: The force of a truss is shown in the figure below. What is the internal force of each member of the…

A:

Q: ) Replace the parallel force system acting on the plate by a resultant force and specify its…

A:

Q: The beam in the figure has a rectangular cross section of dimensions b and h and is subject to when…

A: Allowable normal voltage (ANV) = 1400 kgf/cm2 = 1.4 x 107 kgf/m2 = 1.4 x 104 tf/m2 Ratio of b/h =…

Q: 4 3m t 4m t Sm 5m 3m 4m

A:

Q: 5.66 For the beam shown in the fi above the bottom of the beam at secti A 1.5 m B 14 kN ,C 3 m

A:

Q: A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of…

A: Given data: Length of cantilever beam=4m Outer dia=45 mm Inner dia=35 mm Allowable stress=150 Mpa…

Q: Solve

A:

Q: Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300 lb…

A: Given data in question  Load Angle To find out  Components

Q: The system shown is in static equilibrium and motionless. All joints are ideal. • The origin of the…

A:

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A:

Q: figure this problem

A:

Q: Figure STS 003 shows a pole acted upon by three forces. Select the correct response: 4500.0 3842.2…

A: Given: Required : Value of couple in equivalent couple force system

Q: 1. Suppose that P=104lbs. What will the force Q be in this case? 2. Suppose that P=91lbs. What will…

A:

Q: As shown on the figure is a bar supported by two cables. If the bar has a mass of FN kilograms and…

A:

Q: To facilitate shifting the position of a lifting hook when it is not under load, the sliding hanger…

A: Given:- The sliding hanger is shown  The mass supported by the hook = 202 kg  The value of x = 0.34…

Q: The rigid beam hidden in the figure is fixed at the top by two posts (dext = 50mm), one in AISI 4340…

A:

Q: Resolve the 300-lb force into components along (a) the x- and y axes and (b) the x'- and y-axes 200…

A: Hi there! by mistake, you have provided different force in the figure and the question body so, I am…

Q: 200 mm A 40 mm 50 N 20 mm B. 300 N 250 N 160 mm 100 mm 120 N

A:

Q: The bar composed of aluminum was sustained by the 14 mm2 cross-sectional area of the pin-connected…

A: The given data is shown below: Cross-sectional area=14 mm2E=68.9×109 Pa

Q: Can you show how 184 appear? This is the problem: The beam shown in figure is 5 inches wide and 10…

A:

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

A: As per company's guidelines we can only answer first three questions.  Kindly post other questions…

Q: What is the horizontal support reaction Rax at support A for the frame shown?

A:

Q: Using the method of virtual work, determine the VERTICAL displacement of joint C on the truss loaded…

A: Tension as taken as positive and compression as negative. When a member is connected with two hinge…

Q: A 2 m long cantilever beam is fixed at the right end and carries a 2 kN concentrated load at the…

A:

Q: Select the answer that most nearly gives the axial force on member ad from the real structure in…

A: The given figure is shown below:

Q: 4.5m 4 m 25 mm diameter A 3 m 2.5 m B 0.8m W A bar AB (A = 500mm²) is hinged at A and is supported…

A:

Q: Asap

A:

Q: Q5. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown…

A: Given: The load P is 1 kN. The modulus of elasticity E is 2 x 1011 N/m2. The length L is 1 m. The…

Q: 2. From the given overhanging beam below, calculate the location of maximum moment from point A and…

A: Force in the vertical direction,RA + RD = 12×50×4 + 50 + 40⇒RA + RD = 190KN       .....1Sum of the…

Q: 2. For the truss shown in Figure 2: (Take, A= 30 mm and E= 200 Gpa for all members) a) Find the…

A:

Q: 228 kN B 2.5 m А 4.0 m 4.0 m Shown in the figure above is a truss (E = 300GPA) with 228kN loading.…

A:

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.