Current Attempt in Progress The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw= 16 mm d = 100 mm t = 9.6 mm Additionally: • The area of each pipe is A - 2726 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz=245460000 mm4. If the beam will be subjected to a shear force of V = 275 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. HV Ун YK H K h tw

Current Attempt in Progress The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw= 16 mm d = 100 mm t = 9.6 mm Additionally: • The area of each pipe is A - 2726 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz=245460000 mm4. If the beam will be subjected to a shear force of V = 275 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. HV Ун YK H K h tw

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

16
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
A laminated plastic beam of square cross section is built up by gluing together three strips, each 20 mm x 60 mm in cross section (see figure). The beam has a total weight of 4 N and is simply supported with span length L = 400 mm. м 20 mm 20 mm 60 mm 20 mm 60 mm Considering the weight of the beam (q) calculate the maximum permissible CCWW moment M that may be placed at the right support. (a) If the allowable shear stress in the glued joints is 0.3 MPa. Round to the nearest tenth. Mmax =| N-m (b) If the allowable bending stress in the plastic is 8 MPa. Round to the nearest hundredth. Mmax N.m
Two blocks A and B, each having a mass of 7.5 kg, are connected by the linkage shown. Neglect the weight of the links. (Figure 1) Figure O 30° 30 30° 1 of 1 Part A If the coefficient of static friction at the contacting surfaces is μ = 0.5, determine the largest force P that can be applied to pin C of the linkage without causing the blocks to move. Express your answer to three significant figures and include the appropriate units. P = Submit μÅ Value Provide Feedback Request Answer Units ?
A horizontal beam ABC is loaded as shown in the figure below. The distance of the point of contraflexure from end A (in m) is 10kN (327) Ag 0.75m B C k D 1m -
Please solve the problem
Give me right solution
1. Analyze the beam shown in the figure below using Kani's method. Draw BMD. 30KN m 1 SPKN 20KN/m Sm. 1.51 21 Gm. I
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
In the figure, what is the bar force of member EF in kN ? 10 KN 50 KN 40 KN D 4 m 2 m 2 m O 50- C O 50 - T O 40 - C
A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst ≤ 83 MPa, Tal ≤ 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 50 mm Ø 900 mm 2T Aluminum 40 mm Ø Figure P-316 600 mm
Use slope-deflection method to compute the bending moments of element ends for the following structures: 7) Use slope -defle ction Ast 4 4 12 t- 2006 Pa I= 100x 16mm" E = 200 GPa %3D I= 100× 106 mm4 For this question also compute the deflection at Point B.