1. An elastoplastic material with strain hardening has the stress strain relationship shown below. The yield point is as a stress of 600 MPa and strain of 0.003 mm/mm. a. If a bar of this material was loaded to a stress of 650 MPa and then released, what would be the permanent strain? b. What would be the percent increase in yield strength gained by the strain hardening for a? c. A second load to a stress of 625 MPa is then applied. How much strain is expected? Is the deformation elastic, plastic, or a combination? Stress, MPa 11 . 1000 800 600 400 200 0 0 0.02 0.04 Strain, m/m 0.06 0.08

1. An elastoplastic material with strain hardening has the stress strain relationship shown below. The yield point is as a stress of 600 MPa and strain of 0.003 mm/mm. a. If a bar of this material was loaded to a stress of 650 MPa and then released, what would be the permanent strain? b. What would be the percent increase in yield strength gained by the strain hardening for a? c. A second load to a stress of 625 MPa is then applied. How much strain is expected? Is the deformation elastic, plastic, or a combination? Stress, MPa 11 . 1000 800 600 400 200 0 0 0.02 0.04 Strain, m/m 0.06 0.08

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm² stress.
According to the stress – strain curve for a ductile material: A- what is the yield strength? B- What is the ultimate strength? C- Explain with supplemental figure.
Stress analysis
The modulus of elasticity is measured as the secant for a stress at: a) 30% b) 45% c) 25% d) 40%
An elastoplastic material with strain hardening has the stress-strain relation- ship shown in Figure P1.19. The yield point corresponds to 600 MPa stress and 0.003 m/m strain. a. If a bar made of this material is subjected to a stress of 650 MPa and then released, what is the permanent strain? 1000 800 600 400 200 0.02 0.04 0.06 0.08 Strain, m/m FIGURE P1.19 b. What is the percent increase in yield strength that is gained by the strain hardening shown in part (a)? c. After strain hardening, if the material is subjected to a stress of 625 MPa, how much strain is obtained? Is this strain elastic, permanent, or a combi- nation of both? Stress, MPa
3. Briefly discuss the difference between the brittle and ductile materials using the given stress-strain diagram? Brittle Material Ductile Material Strain, € Stress, o
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 900 mm. The cross- sectional dimensions of the beam are by = 37 mm, d1 = 88 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 18 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be applied as shown to the beam.
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 19N/mm2, find the maximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Txy 10 N/mm2
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 33 mm, d₁ = 109 mm, b₂ = 20 mm, d₂ = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 11 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M B A Answer: M = L d₂ N•m b₁ d₁
A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 33 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: €, =710 με and ε,--255 με (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 24 kN, what is the modulus of elasticity for this specimen? Answers: (a) v= (b) E= GPa
I need typing answer urgent
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 11 N/mm², find the minimum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. If the answer is negative do insert the "-" sign. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Ixy 10 N/mm2